1. Introduction
The XPOWER P-230AT Mini Air Mover is a compact and efficient air moving device designed for various drying, cooling, and ventilation tasks. It features a 1/5 HP motor, providing up to 800 cubic feet per minute (CFM) of airflow. The unit includes three adjustable speeds, four drying positions, a built-in timer, and dual power outlets for daisy-chaining multiple units or powering other devices.
2. Safety Information
Read and understand all instructions before using this appliance. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- Always connect the unit to a properly grounded outlet.
- Do not operate the unit with a damaged cord or plug.
- Keep the air mover away from water or wet surfaces to prevent electric shock.
- Ensure all air intakes and outlets are clear of obstructions during operation.
- Do not use the unit in areas where flammable liquids or gases are present.
- Unplug the unit before performing any maintenance or cleaning.
3. Setup
Before initial use, ensure the unit is placed on a stable, level surface. The P-230AT can be positioned in four different angles (0°, 20°, 45°, and 90°) using its built-in kickstand to direct airflow as needed.
Figure 3.1: Front view of the XPOWER P-230AT Mini Air Mover, highlighting the control panel with speed and timer dials.
Connect the 10 ft. industrial power cord to a standard 115V AC grounded electrical outlet. The unit is equipped with dual thermal protection for safety.
Figure 3.2: Side view of the air mover, illustrating the auxiliary power outlets and circuit breaker for daisy-chaining.
The unit features two built-in auxiliary power outlets, allowing you to daisy-chain up to five additional P-230AT units or connect other electrical devices, provided the total output does not exceed 12 amps.
Figure 3.3: Example of multiple P-230AT units connected in a daisy-chain setup for extended coverage.
4. Operating Instructions
The P-230AT is equipped with a speed control switch and a timer dial.
Figure 4.1: Detailed view of the control panel, indicating the speed selector (OFF, 1, 2, 3) and timer dial (ON, 0-180 minutes).
- Speed Selection: Turn the speed control knob to select one of three airflow speeds (1, 2, or 3). Position '1' is the lowest speed, and '3' is the highest.
- Timer Function: The timer dial can be set for continuous operation ('ON') or for a duration of up to 180 minutes (3 hours). To activate the timer, rotate the dial to the desired time setting. The unit will automatically shut off once the set time has elapsed.
- Drying Positions: Adjust the unit's angle to 0°, 20°, 45°, or 90° to optimize airflow direction for specific drying or ventilation needs.
5. Maintenance
Regular maintenance ensures optimal performance and extends the lifespan of your air mover.
- Cleaning: Periodically clean the exterior of the unit with a damp cloth. Ensure the air intake and outlet grilles are free from dust, debris, and pet hair. Do not use harsh chemicals or abrasive cleaners.
- Storage: When not in use, store the air mover in a clean, dry place. The unit is designed to be stacked up to six units high for efficient storage and transportation.
Figure 5.1: XPOWER P-230AT units stacked for compact storage.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Unit does not turn on | No power supply; tripped circuit breaker; timer not set. | Check power connection; reset circuit breaker on unit or wall; ensure timer is set to 'ON' or a specific time. |
| Reduced airflow | Blocked air intake/outlet; motor issue. | Clear any obstructions from grilles; contact customer support if problem persists. |
| Unusual noise | Debris in fan; loose components. | Unplug and inspect for debris; ensure all parts are secure. |
7. Specifications
- Model: P-230AT
- Motor: 1/5 HP
- Air Flow Capacity: 800 CFM
- Speeds: 3
- Drying Positions: 4 (0°, 20°, 45°, 90°)
- Timer: 3-hour (180 minutes) with 'ON' setting
- Amperage: 2.3 Amps (at highest setting)
- Voltage: 115 Volts
- Power Source: Corded Electric
- Product Dimensions: 10.7"D x 12.4"W x 13.3"H (Note: Product Dimensions from specifications show 30"D x 8"W x 6"H, but description states 10.7" x 12.4" x 13.3". Using description's dimensions as they align with 'compact'.)
- Item Weight: 9.9 Pounds
- Housing Material: Injection-molded polypropylene (PP)
- Safety Certifications: ETL/CETL
8. Warranty and Customer Support
The XPOWER P-230AT Mini Air Mover is backed by a 1-year manufacturer's limited warranty. For warranty claims, technical assistance, or customer support, please refer to the official XPOWER website or contact their customer service department directly. Keep your purchase receipt as proof of purchase for warranty validation.
