Rok SCD101
Rok Hardware SCD101 Soft Close Cabinet Door Damper Manual
1. Introduction
Thank you for choosing Rok Hardware Soft Close Cabinet Door Dampers. These dampers are designed to provide a smooth, quiet closing action for your cabinet doors, preventing slamming and reducing wear. This manual provides essential information for proper installation, operation, and maintenance of your SCD101 dampers.
2. Safety Information
- Always use appropriate personal protective equipment, such as safety glasses, during installation.
- Keep small parts and tools out of reach of children to prevent choking hazards or injury.
- Ensure all screws are securely fastened to prevent the damper from detaching.
- Do not overtighten screws, as this may damage the cabinet material.
3. Package Contents
Your Rok Hardware SCD101 Soft Close Cabinet Door Damper package includes:
- 10 x Rok Hardware SCD101 Soft Close Dampers
- 10 x Mounting Screws (1 screw per damper)
4. Compatibility
The Rok Hardware SCD101 Soft Close Dampers are designed for specific cabinet types and hinge configurations:
- Works only with cabinets that have fully concealed self-closing hinges.
- Compatible with face frame cabinets on all door overlays.
- Compatible with frameless cabinets on full overlay doors.
It is recommended to verify your cabinet and hinge type before proceeding with installation.
Image: This diagram illustrates the types of hinges compatible with the SCD101 dampers. The 'YES' side shows a concealed hinge, while the 'NO' side shows a visible hinge, indicating incompatibility.
5. Setup (Installation)
Follow these steps to install your Rok Hardware SCD101 Soft Close Dampers:
- Identify Mounting Location: The damper should be mounted in the upper corner of the cabinet on the side where the hinge is located.
- Prepare Pilot Hole: To prevent damaging your cabinets, drill a pilot hole using a 2.3 mm or 3/32" drill bit, approximately 1/4" deep. This is for a #6 x 3/4" pan head screw.
- Position Damper: Place the damper firmly into the upper corner, aligning the screw hole with your pilot hole.
- Secure Damper: Insert one mounting screw through the damper's hole and tighten it securely. Do not overtighten.
- Test and Adjust: Close the cabinet door to test the soft-close function. If needed, proceed to the 'Operating (Adjustment)' section to fine-tune the closing speed.
For most applications, one damper per door is sufficient. For heavier doors, two or more dampers may be required. Trial mounting is advised before purchasing large quantities.
Image: This diagram illustrates the universal application of the soft close damper in various cabinet constructions, showing placement options and the adjustment screw.
Image: A detailed view of the damper mounting process, including dimensions and the recommended pilot hole size for installation.
Image: This image provides a visual guide for easy installation, showing the damper being screwed into the cabinet corner for both face frame and frameless cabinet types.
6. Operating (Adjustment)
The Rok Hardware SCD101 dampers feature an adjustable mechanism to control the closing speed of your cabinet doors.
- Locate the Phillips head screw mechanism on the back of the damper.
- Turn the adjustment screw in (clockwise) for heavier doors or to achieve a slower closing speed.
- Turn the adjustment screw out (counter-clockwise) for lighter doors or to achieve a faster closing speed.
- Test the door after each adjustment until the desired soft-close motion is achieved.
Image: A close-up view of the adjustment screw, highlighting its function in controlling the soft-closing strength.
Image: This image shows the Rok Soft Close Damper and provides instructions on how to adjust the screw for heavier or lighter doors.
7. Maintenance
The Rok Hardware SCD101 Soft Close Dampers require minimal maintenance.
- Periodically check the mounting screws to ensure they remain tight.
- Wipe the dampers with a soft, dry cloth to remove dust or debris. Avoid using harsh chemicals or abrasive cleaners.
- If the soft-close function changes over time, re-adjust the damper as described in the 'Operating (Adjustment)' section.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Door still slams or closes too quickly. | Damper not adjusted correctly; insufficient damping force for door weight. | Turn the adjustment screw further in (clockwise). If the problem persists, consider adding an additional damper to the door. |
| Door closes too slowly or does not close completely. | Damper adjusted too far in; excessive damping force. | Turn the adjustment screw further out (counter-clockwise). |
| Damper appears loose or ineffective. | Improper installation; loose mounting screw; incompatible hinge type. | Check that the mounting screw is tight. Verify that your cabinet has fully concealed self-closing hinges. Re-install if necessary. |
9. Specifications
- Model: SCD101
- Material: Metal (Zinc Diecast Housing)
- Finish: Brushed Nickel
- Product Dimensions: 2.5"L x 1"W
- Mounting Type: Door Mount, Face
- Hole Count: 1 (per damper)
- Adjustability: Manually adjustable closing speed
- Compatibility: Face frame cabinets (all door overlays), frameless cabinets (full overlay doors), only with fully concealed self-closing hinges.
10. Warranty and Support
For specific warranty information regarding your Rok Hardware SCD101 Soft Close Cabinet Door Dampers, please refer to the product packaging or contact Rok Hardware directly. For technical support or further assistance, please visit the official Rok Hardware website or contact their customer service department.
Rok Hardware Website: Rok Store on Amazon
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.