Introduction
This manual provides essential information for the safe and efficient installation, operation, and maintenance of your FLOS Foglio Wall Lamp.
Designed by Tobia Scarpa in 1966, the Foglio lamp is a classic wall-mounted fixture providing direct, indirect, and partially diffused light. This product is intended for indoor use only.
Image: Front view of the FLOS Foglio Wall Lamp, showcasing its distinctive curved design.
Safety Information
WARNING: Electrical installation should only be performed by a qualified electrician in accordance with local electrical codes and regulations.
- Always disconnect power at the main circuit breaker before attempting any installation, maintenance, or bulb replacement.
- Do not exceed the maximum wattage specified for the light bulbs (2 x max 100W E27).
- This product is designed for indoor use only and is not water-resistant. Avoid exposure to moisture.
- Ensure the lamp is securely mounted to a stable wall surface capable of supporting its weight.
Product Components
The FLOS Foglio Wall Lamp includes the following main components:
- Polished white powder-coated steel diffuser
- Two injection-molded lamp holders (E27 base)
- Mounting plate and associated hardware
Note: Light bulbs are not included and must be purchased separately.
Setup and Installation
Installation requires assembly and wall mounting. It is strongly recommended to have this procedure performed by a professional electrician to ensure safety and proper function.
Tools Required (Not Included):
- Screwdrivers (Phillips and Flathead)
- Wire strippers
- Electric drill
- Measuring tape and pencil
- Wall anchors (if necessary for your wall type)
Installation Steps:
- Prepare the Installation Area: Before beginning, ensure the power supply to the installation area is turned off at the main circuit breaker. Verify with a voltage tester.
- Mount the Backplate: Secure the lamp's mounting plate to the wall using appropriate screws and anchors for your wall type. Ensure it is level and firmly attached.
- Connect Electrical Wiring: Connect the household electrical wires to the lamp's wiring according to the provided wiring diagram and local electrical codes. Ensure all connections are secure using wire nuts and properly insulated.
- Install Lamp Holders: Attach the two injection-molded lamp holders securely within the steel diffuser.
- Attach Diffuser to Backplate: Carefully align the steel diffuser with the mounted backplate and secure it using the provided fasteners. Ensure it is stable and flush against the wall.
- Insert Light Bulbs: Screw two E27 base light bulbs (max 100W each, halogen or LED compatible) into the lamp holders. Do not overtighten.
- Restore Power: Once installation is complete and all connections are secure, restore power at the main circuit breaker.
Image: A detailed view of the lamp's mounting plate, showing screw holes for secure wall attachment.
Image: Rear view of the FLOS Foglio lamp, highlighting the central mounting plate and the area for electrical connections.
Image: A detailed view of one of the E27 lamp holders positioned inside the diffuser, ready for bulb insertion.
Operating Instructions
The FLOS Foglio Wall Lamp is designed for use with a compatible dimmer switch (not included) for adjustable light intensity. The lamp itself does not have an integrated switch.
- Turning On/Off: Use the wall switch connected to the lamp to turn it on or off.
- Dimming: If connected to a compatible dimmer switch, adjust the light intensity by manipulating the dimmer control. Ensure your chosen bulbs are dimmable.
Maintenance
Regular maintenance will help preserve the appearance and functionality of your FLOS Foglio Wall Lamp.
- Cleaning: To clean the lamp, always ensure power is disconnected at the circuit breaker. Wipe the polished steel diffuser with a soft, dry, or slightly damp cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish.
- Bulb Replacement: Disconnect power before replacing bulbs. Allow old bulbs to cool completely before handling. Unscrew old bulbs counter-clockwise and replace with new E27 base bulbs, ensuring they do not exceed 100W each.
Troubleshooting
If you encounter issues with your FLOS Foglio Wall Lamp, refer to the following table for common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not light up | No power supply Faulty wiring connection | Check the circuit breaker and wall switch. Ensure all electrical connections are secure. Consult a qualified electrician if unsure. |
| One or both bulbs not working | Faulty bulb Bulb not screwed in properly | Replace the light bulb. Ensure the bulb is screwed in firmly. |
| Flickering light | Loose connection Incompatible dimmer or bulb | Check bulb seating and electrical connections. Ensure your dimmer switch and bulbs are compatible (e.g., LED dimmable bulbs with an LED-compatible dimmer). |
Specifications
Detailed technical specifications for the FLOS Foglio Wall Lamp:
| Feature | Detail |
|---|---|
| Model Name | FOGLIO |
| Model Number | F2400009 |
| Brand | FLOS |
| Designer | Tobia Scarpa (1966) |
| Color | White |
| Material | Alloy Steel |
| Dimensions (L x W x H) | 37 cm x 9.7 cm x 21 cm (14.57" x 3.82" x 8.27") |
| Weight | 3.63 Kilograms |
| Light Source | 2 x E27 base bulbs (not included) |
| Max Wattage per Bulb | 100W |
| Voltage | 220 Volt |
| Light Direction | Incandescent (Direct, Indirect, Partially Diffused) |
| Control Method | Touch (via compatible dimmer switch) |
| Switch Type | Dimmer compatible |
| Recommended Use | Indoor, Living Room, Workspace |
| Water Resistance Level | Not water-resistant |
| Energy Efficiency Label | C (EU Label) |
| Assembly Required | Yes |
| Country of Origin | Italy |
| GTIN (Global Trade Item Number) | 04052313081661 |
Warranty and Support
This product comes with a limited warranty. Please refer to your purchase documentation or the official FLOS website for specific warranty terms and conditions applicable to your region.
For technical support, service inquiries, or replacement parts, please contact FLOS customer service or your authorized dealer. Keep your proof of purchase for warranty claims.
