Burndy KS29

Download PDF
Contents

BURNDY KS29 Split-Bolt Connector Instruction Manual

Model: KS29 | Brand: Burndy

1. Product Overview

The BURNDY KS29 is a high-quality copper split-bolt connector designed for making reliable electrical connections. It is suitable for connecting copper conductors ranging from 1 AWG to 250 KCMIL, facilitating both run and tap connections. This connector is engineered for durability and performance in various electrical applications.

BURNDY KS29 Split-Bolt Connector, side view

Figure 1: Side view of the BURNDY KS29 Split-Bolt Connector, showing its robust copper construction and the integrated bolt mechanism.

2. Safety Information

WARNING: Electrical shock hazard. Always disconnect power before installing or servicing electrical connectors. Installation should only be performed by qualified personnel in accordance with all applicable national and local electrical codes.

  • Always wear appropriate personal protective equipment (PPE), including insulated gloves and safety glasses.
  • Ensure the conductors are de-energized before making any connections.
  • Verify proper wire gauge compatibility with the connector.
  • Do not overtighten or undertighten the bolt; refer to torque specifications if available or use appropriate tools for secure connection.

3. Setup and Installation

Follow these steps for proper installation of the BURNDY KS29 Split-Bolt Connector:

  1. Prepare Conductors: Strip the insulation from the ends of the copper conductors to be connected. The length of the stripped portion should be sufficient to allow the conductors to fully seat within the connector's jaws. Ensure the conductors are clean and free of oxidation.
  2. Insert Conductors: Loosen the split-bolt sufficiently to open the jaws. Insert the main (run) conductor into one side of the connector and the tap conductor into the other side. Ensure both conductors are fully seated within the connector's grooves.
  3. Close-up view of the BURNDY KS29 Split-Bolt Connector's internal jaws

    Figure 2: Close-up view of the connector's internal jaws, designed to securely grip the conductors.

  4. Tighten Connection: Using an appropriate wrench, tighten the split-bolt. Apply firm and even pressure to ensure a secure mechanical and electrical connection. Continue tightening until the conductors are firmly gripped and the connector is snug. Avoid over-tightening, which can damage the conductors or the connector.
  5. Inspect Connection: After tightening, visually inspect the connection to ensure the conductors are properly seated and the connector is secure.
  6. Insulate Connection: Once the connection is complete and verified, insulate the exposed metal parts of the connector and conductors using appropriate electrical tape or heat-shrink tubing, as required by local electrical codes.

4. Operating Instructions

The BURNDY KS29 is a passive electrical connector. Its 'operation' is primarily its proper installation, which ensures a continuous and reliable electrical path. Once installed correctly, it requires no further active operation. Regular inspection (see Maintenance section) is recommended to ensure continued performance.

5. Maintenance

To ensure the longevity and reliability of your electrical connections, periodic maintenance is recommended:

  • Visual Inspection: Periodically inspect installed connectors for any signs of corrosion, discoloration (indicating overheating), or physical damage.
  • Tightness Check: If accessible and safe to do so (with power disconnected), gently check the tightness of the split-bolt. Do not re-tighten unless necessary, and always adhere to safety protocols.
  • Environmental Factors: Ensure the connector is not exposed to excessive moisture, corrosive chemicals, or extreme temperatures beyond its specified operating range, unless properly protected.

6. Troubleshooting

Most issues with split-bolt connectors stem from improper installation. If you experience problems, consider the following:

  • Poor Connection/High Resistance:
    Possible Cause: Insufficient tightening of the bolt.
    Solution: Disconnect power, re-tighten the bolt securely. Ensure conductors are clean and properly seated.
    Possible Cause: Incorrect wire gauge or material.
    Solution: Verify that the conductors are copper and within the 1 AWG-250 KCMIL range.
  • Overheating at Connection Point:
    Possible Cause: Loose connection or inadequate contact area.
    Solution: Disconnect power, re-inspect and re-install the connector, ensuring proper conductor seating and tightening.
  • Physical Damage to Connector:
    Possible Cause: Overtightening or external impact.
    Solution: Replace the damaged connector with a new one.

If issues persist, consult a qualified electrician.

7. Specifications

Bottom view of BURNDY KS29 Split-Bolt Connector showing model number and certifications

Figure 3: Bottom view of the connector, displaying the model number 'KS29' and 'BURNDY' branding, along with UL and CSA certification marks.

SpecificationValue
Model NumberKS29
BrandBurndy
Contact MaterialCopper
Wire Gauge Range1 AWG - 250 KCMIL
Product Dimensions1.6 x 1.4 x 1.6 inches
Item Weight6.24 ounces
Specification MetCSA, UL
Temperature Rating221 degrees Celsius

8. Warranty and Support

For information regarding product warranty, technical support, or any other inquiries, please contact Burndy directly through their official website or customer service channels. Keep your purchase receipt for warranty claims.

Burndy Official Website: www.burndy.com

© 2024 Burndy. All rights reserved. This manual is for informational purposes only.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.