1. Introduction
This manual provides detailed instructions for the safe and effective installation and use of the Burndy KS22 Split-Bolt Connector. This connector is designed for joining copper conductors, specifically accommodating 6 Stranded (Str) to 2 Solid (Sol) wire gauges. Please read this manual thoroughly before installation to ensure proper application and safety.
2. Safety Information
WARNING: Electrical work should only be performed by qualified personnel. Failure to follow these safety instructions can result in electric shock, fire, or serious injury.
- Always disconnect power before installing or working with electrical connectors.
- Use appropriate personal protective equipment (PPE), including insulated gloves and safety glasses.
- Ensure all connections are made in accordance with local and national electrical codes.
- Verify the correct wire gauge and type for the connector.
- Do not reuse damaged connectors.
3. Product Overview
The Burndy KS22 is a high-strength, high-conductivity split-bolt connector manufactured from copper alloy. It is designed for making tap, splice, or parallel connections of copper conductors. The split-bolt design allows for easy installation and provides a secure, reliable electrical connection.

Figure 1: Burndy KS22 Split-Bolt Connector. This image displays the copper-colored connector, featuring a threaded bolt and a hexagonal nut designed for securing electrical wires within its split body.
Key Features:
- Material: High-conductivity copper alloy.
- Conductor Range: Accommodates 6 Stranded (Str) to 2 Solid (Sol) copper conductors.
- Application: Suitable for tap, splice, and parallel connections.
- Compliance: UL Listed and CSA Certified, ensuring adherence to safety and performance standards.
4. Installation Instructions
Follow these steps for proper installation of the Burndy KS22 Split-Bolt Connector:
- Prepare Conductors: Strip the insulation from the ends of the copper conductors to be joined. The stripped length should be sufficient to allow the conductors to fully enter the connector body without insulation entering the contact area. Ensure the conductors are clean and free of oxidation.
- Insert Conductors: Loosen the nut on the split-bolt connector. Insert the main conductor into one side of the split-bolt and the tap or parallel conductor into the other side. Ensure both conductors are seated firmly within the connector's grooves.
- Tighten Connection: Using an appropriate wrench, tighten the hexagonal nut on the split-bolt. Apply sufficient torque to ensure a secure mechanical and electrical connection. The bolt should be tightened until the connector firmly grips both conductors, preventing any movement. Refer to manufacturer's recommended torque specifications if available, or tighten until the bolt is snug and the conductors are visibly compressed.
- Inspect Connection: Visually inspect the connection to ensure that no bare wire strands are exposed beyond the connector body and that the conductors are securely held. Gently tug on the wires to confirm they are not loose.
- Insulate Connection: Once the connection is secure, insulate the entire connector and exposed wire ends using appropriate electrical tape or heat-shrink tubing to prevent accidental contact and short circuits.
Note: For optimal performance and safety, ensure the conductors are within the specified range of 6 Stranded to 2 Solid copper wire.
5. Maintenance
The Burndy KS22 Split-Bolt Connector is designed for long-term, maintenance-free operation once properly installed and insulated. However, periodic inspection of electrical connections is recommended as part of a general electrical system maintenance program.
- Visual Inspection: During routine electrical system checks, visually inspect the insulated connection for any signs of damage, overheating (discoloration), or insulation degradation.
- Environmental Factors: Ensure the connection remains protected from moisture, corrosive agents, and excessive mechanical stress.
If any issues are observed, disconnect power and consult a qualified electrician for assessment and repair.
6. Troubleshooting
Most issues with split-bolt connectors arise from improper installation. If an electrical circuit connected with a Burndy KS22 connector is not functioning correctly, consider the following:
- No Power/Intermittent Power:
- Loose Connection: The most common cause. Power off the circuit, remove insulation, and re-tighten the nut on the split-bolt connector to ensure a firm grip on both conductors.
- Incorrect Wire Gauge: Ensure the conductors used are within the specified range (6 Stranded to 2 Solid). Wires that are too small may not be securely gripped, and wires that are too large may not fit properly or create excessive stress.
- Poor Conductor Preparation: Insufficiently stripped wires or oxidized conductors can lead to poor electrical contact. Power off, remove insulation, and re-prepare the wire ends if necessary.
- Overheating/Discoloration:
- Loose Connection: A loose connection can cause high resistance and generate heat. Re-tighten the connection.
- Overload: Ensure the circuit is not overloaded beyond the capacity of the conductors or the connector. Consult an electrician if overloading is suspected.
- Corrosion: If the connection was exposed to moisture or corrosive elements, corrosion can increase resistance. Replace the connector if corrosion is present.
If troubleshooting steps do not resolve the issue, consult a qualified electrician.
7. Specifications
| Model Number | KS22 |
| Brand | Burndy |
| Connector Type | Split-Bolt, Screw Type |
| Contact Material | Copper Alloy |
| Conductor Range | 6 Stranded (Str) to 2 Solid (Sol) Copper |
| Terminal | Ring Terminal |
| Product Dimensions | 1.5 x 0.7 x 0.7 inches |
| Weight | 4.01 Pounds |
| Certifications | UL Listed, CSA Certified |
8. Warranty and Support
Burndy products are manufactured to high-quality standards. For specific warranty information, please refer to the official Burndy website or contact Burndy customer support directly. Keep your purchase receipt for warranty claims.
For technical assistance or further inquiries, please visit the official Burndy website or contact their customer service department.