1. Introduction
This manual provides essential instructions for the proper installation, operation, and maintenance of your DeVilbiss 803018 StartingLine 1.8mm Replacement Tip/Needle Set. This set is designed to restore optimal performance to compatible DeVilbiss StartingLine spray guns. Please read these instructions thoroughly before attempting any installation or use.
2. Product Overview
The DeVilbiss 803018 set includes a 1.8mm fluid tip and a corresponding fluid needle, essential components for controlling material flow and atomization in your spray gun.

Figure 1: The DeVilbiss 803018 StartingLine 1.8mm Replacement Tip/Needle Set. This image displays the two primary components: a silver-colored fluid tip with multiple small holes and a central opening, and a long, slender silver-colored fluid needle with a brass collar in the middle. These parts are crucial for precise material delivery in a spray gun.
3. Setup and Installation
Proper installation is critical for optimal spray gun performance and safety. Always ensure the spray gun is disconnected from air supply and completely depressurized before beginning any maintenance or part replacement.
- Safety First: Disconnect the spray gun from the air supply. Ensure all material has been drained and the gun is clean.
- Remove Old Components: Carefully unscrew and remove the existing air cap, fluid tip, and fluid needle from your DeVilbiss StartingLine spray gun. Refer to your specific spray gun's manual for detailed disassembly instructions.
- Inspect and Clean: Thoroughly clean the spray gun body, especially the threads and seating areas where the new tip will be installed. Inspect for any damage or debris.
- Install New Fluid Tip: Gently thread the new 1.8mm fluid tip into the spray gun body. Hand-tighten only, then use a wrench to snug it securely, but do not overtighten. Overtightening can damage the tip or gun body.
- Install New Fluid Needle: Insert the new fluid needle into the rear of the spray gun, guiding it through the packing nut and into the fluid tip. Ensure it seats correctly.
- Reassemble: Reattach the air cap, ensuring it is properly aligned and tightened.
- Test: Reconnect the air supply and perform a test spray with appropriate material to check for proper function, leaks, and spray pattern. Adjust fluid and air controls as needed.
4. Operating Guidelines
Once installed, the 1.8mm tip and needle set is suitable for spraying a variety of medium to heavy viscosity materials. Always refer to the material manufacturer's recommendations for specific spray gun settings, including fluid pressure, air pressure, and spray distance.
- Material Compatibility: The 1.8mm size is generally used for primers, sealers, and some heavier topcoats.
- Adjustments: Fine-tune the fluid control knob to regulate the amount of material, and the air control valve to adjust atomization.
- Spray Pattern: Test the spray pattern on a scrap surface before applying to your workpiece. Adjust as necessary for an even, consistent finish.
5. Maintenance
Regular cleaning and maintenance will extend the life of your tip/needle set and ensure consistent performance.
- Immediate Cleaning: After each use, thoroughly clean the fluid tip and needle. Disassemble the air cap, fluid tip, and needle.
- Solvent Use: Use appropriate cleaning solvents recommended by your material manufacturer. Never use metal objects to clean the fluid tip or air cap holes, as this can damage them.
- Inspection: Regularly inspect the fluid tip and needle for wear, damage, or dried material. Replace if wear is evident or performance degrades.
- Storage: Store components in a clean, dry place to prevent corrosion and damage.
6. Troubleshooting
If you experience issues after installing the new tip/needle set, consider the following:
- Poor Spray Pattern: Check if the fluid tip is securely tightened and not cross-threaded. Ensure the air cap is clean and correctly aligned. Verify the fluid needle is seating properly.
- Leaking from Tip: The fluid needle may not be seating correctly, or the fluid tip might be damaged or not fully tightened.
- No Material Flow: Ensure the fluid needle is not stuck or obstructed. Check for dried material in the fluid tip.
- Inconsistent Flow: This could indicate partial blockage in the fluid tip or an issue with the fluid needle's movement.
7. Specifications
| Feature | Detail |
|---|---|
| Brand | DeVilbiss |
| Model Number | 803018 |
| Tip Size | 1.8mm |
| Product Type | Replacement Tip/Needle Set |
| Package Dimensions (L x W x H) | 21.336 cm x 6.35 cm x 2.286 cm |
| Country Of Origin | Taiwan |
8. Support and Warranty
For technical assistance, replacement parts, or warranty information, please contact DeVilbiss customer support directly. Refer to the official DeVilbiss website or your original spray gun manual for contact details.