Teleco TXP-868-A01

TELECO TXP-868-A01 Remote Control User Manual

Model: TXP-868-A01 | Brand: TELECO

1. Introduction

This user manual provides comprehensive instructions for the TELECO TXP-868-A01 remote control. This remote operates at a frequency of 868.3 MHz and features a single button for controlling gate systems. It is designed for ease of use and simple programming, requiring no special equipment.

The TELECO TXP-868-A01 is compatible with TV-LINK TXP-868-A01 gate remote controls.

2. Product Overview

TELECO TXP-868-A01 Remote Control

Figure 2.1: Front view of the TELECO TXP-868-A01 remote control, showing its single button and compact design.

Key Features:

  • Gate remote control with 868.3 MHz frequency.
  • Programming type: Registration in the receiver.
  • Battery type: CR2032.
  • Compact dimensions: 59 mm x 33 mm x 13 mm.
  • Includes battery and programming instructions.

3. Setup and Programming

The TELECO TXP-868-A01 remote control is programmed by registering it directly into your gate receiver. This process is generally straightforward and does not require specialized equipment.

Programming Steps (General Guide):

  1. Locate the programming button on your gate receiver unit. This button is often labeled "PROG", "MEM", or "LEARN". Refer to your gate system's receiver manual for its exact location and function.
  2. Press and hold the programming button on the receiver until an indicator light (LED) on the receiver illuminates or changes state, indicating it is in programming mode.
  3. While the receiver is in programming mode, press the button on your new TELECO TXP-868-A01 remote control that you wish to program. Hold the button for a few seconds.
  4. The indicator light on the receiver should flash, change color, or turn off, confirming that the remote control has been successfully registered.
  5. Wait a few seconds for the receiver to exit programming mode automatically, or press the programming button on the receiver again briefly to exit.
  6. Test the remote control by pressing its button. The gate should respond.

Note: Specific programming procedures may vary depending on your gate receiver model. Always consult the instruction manual for your gate system's receiver for precise programming steps.

4. Operating Instructions

Once programmed, operating the TELECO TXP-868-A01 remote control is simple.

Basic Operation:

  • To open or close your gate, point the remote control towards the gate receiver (if line of sight is required) and press the programmed button once.
  • The gate will initiate its programmed action (e.g., open, close, stop).
  • Ensure you are within the operational range of the receiver (up to 10 meters, depending on environmental factors).

5. Maintenance

Battery Replacement:

The remote control is powered by a CR2032 lithium coin cell battery. If the remote's range decreases significantly or it stops responding, the battery may need replacement.

  1. Locate the battery compartment on the back or side of the remote control. It may be secured with a small screw or a snap-on cover.
  2. Carefully open the compartment using a small screwdriver or by prying gently with a flat tool.
  3. Remove the old CR2032 battery. Note its orientation (positive (+) side up or down).
  4. Insert a new CR2032 battery, ensuring the correct polarity.
  5. Close the battery compartment securely.
  6. Test the remote control to ensure proper function.

Cleaning:

Clean the remote control with a soft, dry cloth. Do not use abrasive cleaners or immerse the remote in water.

6. Troubleshooting

ProblemPossible CauseSolution
Remote control does not work.Battery is dead or incorrectly inserted.Replace the CR2032 battery, ensuring correct polarity.
Remote control has reduced range.Low battery. Interference. Obstructions.Replace battery. Ensure no strong radio interference sources nearby. Reduce obstructions between remote and receiver.
Gate does not respond after programming.Incorrect programming procedure. Remote not registered.Repeat the programming steps carefully, referring to your gate receiver's manual. Ensure the receiver enters and exits programming mode correctly.
Remote control button feels stuck.Debris under the button.Gently clean around the button with a soft, dry cloth or compressed air. Do not force the button.

7. Specifications

FeatureDetail
BrandTELECO
Model NameTXP-868-A01
Connectivity TechnologyRadio Frequency (RF)
Frequency868.3 MHz
Number of Buttons1
Compatible DevicesGate systems (compatible with TV-LINK TXP-868-A01)
Battery Type1 x CR2032 Lithium battery
Dimensions (L x W x H)59 mm x 33 mm x 13 mm
Maximum Range10 Meters (approximate, depends on environment)
Rechargeable BatteryNo

8. Warranty and Support

Warranty Information:

This TELECO TXP-868-A01 remote control comes with a 1-year warranty from the date of purchase. This warranty covers manufacturing defects. Please retain your proof of purchase for warranty claims.

The warranty does not cover damage caused by misuse, unauthorized modifications, accidents, or normal wear and tear, including battery depletion.

Customer Support:

For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact your retailer or the official TELECO support channels. Refer to the packaging or the official TELECO website for contact information.

© 2024 TELECO. All rights reserved.

This manual is for informational purposes only. Specifications are subject to change without notice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.