Introduction
This manual provides essential instructions for the installation, operation, and maintenance of your Urmet 1133/1 Electronic Intercom Handset Atlantique. Please read this guide thoroughly before attempting to install or operate the device to ensure proper function and safety. This handset is designed for clear audio communication within an intercom system.
Product Overview
Image: The Urmet 1133/1 Electronic Intercom Handset Atlantique, shown in white, featuring a classic design with a receiver and base unit.
The Urmet 1133/1 is an electronic intercom handset, part of the Atlantique series, designed for reliable audio communication in residential or commercial intercom systems. It features a robust construction and simple interface for user convenience.
Setup
Proper installation is crucial for the optimal performance of your Urmet 1133/1 intercom handset. It is recommended that installation be performed by a qualified technician.
1. Mounting the Handset
- Choose a suitable location on a wall, typically near an entrance or in a central area, ensuring it is within reach and at an appropriate height.
- Mark the drilling points using the handset's mounting plate as a template.
- Drill holes and insert wall plugs if necessary.
- Secure the mounting plate to the wall using appropriate screws.
2. Wiring Connections
- Before making any electrical connections, ensure the main power supply to the intercom system is turned OFF at the circuit breaker.
- Refer to the wiring diagram provided with your specific intercom system for correct terminal connections. The Urmet 1133/1 typically connects to the main intercom bus with specific terminals for audio in, audio out, call signal, and door release (if applicable).
- Carefully strip the insulation from the wires and connect them to the corresponding terminals on the handset's base unit. Ensure all connections are secure and free from short circuits.
- Once wiring is complete, attach the handset to the mounting plate.
3. Power On and Test
- Restore power to the intercom system.
- Test the handset by initiating a call from the outdoor unit or another internal unit.
- Verify that the call tone is audible, two-way speech is clear, and any associated functions (e.g., door release) operate correctly.
Operating Instructions
The Urmet 1133/1 handset provides straightforward operation for managing intercom calls.
Receiving a Call
- When a visitor presses the call button on the outdoor unit, the handset will emit a distinctive ring tone.
- Lift the handset from its cradle to answer the call.
- Speak clearly into the microphone and listen for the visitor's response.
- To end the conversation, simply replace the handset in its cradle.
Door Release Function (if applicable)
- During an active conversation, press the dedicated door release button (if present on your model) to unlock the entrance.
- The door will typically remain unlocked for a short period before automatically re-locking.
Maintenance
Regular maintenance ensures the longevity and reliable performance of your intercom handset.
Cleaning
- Clean the exterior of the handset with a soft, dry, or slightly damp cloth.
- Do not use abrasive cleaners, solvents, or strong chemical agents, as these can damage the plastic surfaces.
- Ensure no liquid enters the internal components of the handset.
General Care
- Avoid dropping the handset or subjecting it to strong impacts.
- Keep the handset away from excessive moisture, direct sunlight, and extreme temperatures.
- Do not attempt to open the handset casing, as this may void the warranty and expose you to electrical hazards.
Troubleshooting
If you encounter issues with your Urmet 1133/1 handset, refer to the following common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| No sound from handset speaker or microphone. | Loose wiring connection; faulty handset; system power issue. | Check wiring connections at the handset and main system. Ensure system power is on. If problem persists, contact a qualified technician. |
| Handset does not ring when called. | Incorrect wiring; call button on outdoor unit not functioning; system fault. | Verify call signal wiring. Test the outdoor unit's call button. Consult system manual or technician. |
| Door release function not working. | Door release wiring issue; faulty door strike/lock; system fault. | Check door release wiring. Ensure the door strike/lock is receiving power and functioning. Contact a technician if necessary. |
| Interference or poor audio quality. | Electrical interference; damaged wiring; faulty components. | Ensure wiring is properly shielded and away from power cables. Inspect wiring for damage. If problem persists, professional inspection is recommended. |
Specifications
Key technical specifications for the Urmet 1133/1 Electronic Intercom Handset Atlantique:
- Manufacturer: URMET
- Model Number: 1133/1
- Color: White
- Package Dimensions: 25.4 x 10.4 x 6.6 cm (10 x 4.1 x 2.6 inches)
- Item Weight: Approximately 399.16 grams (0.88 pounds)
- Quantity of Items: 1
- Battery(ies) Included: No
- Battery(ies) Required: No
- Discontinued by Manufacturer: No
- Spare Parts Availability: Information unavailable
- Software Updates Guaranteed Until: Information not available
- Date First Available on Amazon.com.be: September 11, 2015
Warranty and Support
For warranty information, please refer to the documentation provided at the time of purchase or contact your retailer. Urmet products typically come with a manufacturer's warranty covering defects in materials and workmanship.
For technical support, spare parts, or service inquiries, please contact Urmet customer service or visit the official Urmet website. Ensure you have your model number (1133/1) and purchase details ready when contacting support.
Urmet Official Website: www.urmet.com (Please note: This link is a general example and may need to be updated to a region-specific Urmet site for accurate support.)
