YONGNUO YN560 III

Download PDF
Contents

YONGNUO YN560 III Speedlite Flash Instruction Manual

Model: YN560 III

1. Introduction

The YONGNUO YN560 III is a high-performance manual speedlite flash designed for various DSLR cameras, including Canon, Nikon, Pentax, and Olympus. It features a built-in 2.4GHz wireless receiver, offering versatile off-camera flash capabilities. This manual provides detailed instructions for proper setup, operation, and maintenance of your YN560 III flash unit to ensure optimal performance and longevity.

2. Safety Information

Please read and understand all safety precautions before using this product. Improper use may result in injury or damage to the device.

  • Do not disassemble or attempt to repair the flash unit yourself. Refer all servicing to qualified personnel.
  • Keep the flash unit dry. Do not expose it to water or high humidity.
  • Avoid direct eye exposure to the flash light, especially at close range, as it can cause temporary vision impairment.
  • Use only specified AA batteries. Do not mix old and new batteries or different types of batteries.
  • Remove batteries if the flash unit will not be used for an extended period.
  • Keep out of reach of children.
  • Do not operate the flash in the presence of flammable gases or liquids.
  • Ensure the flash is securely mounted to prevent accidental drops.

3. Package Contents

Verify that all items are present in your package:

  • YONGNUO YN560 Mark III Speedlite Flash
  • Mini Stand
  • Protective Bag
  • Instruction Manual
Yongnuo YN560 III package contents including flash, stand, and manual

Image 3.1: The YN560 III flash unit, mini stand, and user manual as typically included in the package.

4. Setup

4.1 Battery Installation

  1. Open the battery compartment cover located on the side of the flash unit.
  2. Insert four (4) AA-size batteries according to the polarity indicators (+/-) inside the compartment.
  3. Close the battery compartment cover securely until it clicks into place.
Yongnuo YN560 III flash with battery compartment open, showing four AA batteries inserted

Image 4.1: Proper insertion of four AA batteries into the YN560 III flash unit. Batteries are not included.

4.2 Mounting the Flash

The YN560 III can be mounted on a camera's hot shoe or on the included mini stand for off-camera use.

  • On Camera Hot Shoe: Slide the flash's mounting foot into your camera's hot shoe. Rotate the locking ring clockwise until the flash is securely fastened.
  • On Mini Stand: Attach the flash to the mini stand by sliding the flash foot into the stand's slot. The mini stand allows the flash to be placed on a flat surface or mounted on a light stand via its threaded socket.
Detailed view of the Yongnuo YN560 III flash hot shoe contact and USB/PC sync port

Image 4.2: The hot shoe contact and PC sync port for connecting the flash to a camera or trigger.

5. Operation

5.1 Power On/Off

Press and hold the ON/OFF button for approximately 2 seconds to power the flash on or off.

5.2 Controls and Display

The YN560 III features an intuitive control panel and LCD display for easy adjustments.

Front view of the Yongnuo YN560 III flash showing the LCD screen and control buttons

Image 5.1: The main control panel with LCD display, directional buttons, and mode selection.

  • MODE Button: Cycles through flash modes (M, Multi, S1, S2, RX).
  • PILOT Button: Test flash button. Also indicates flash readiness (red light).
  • Directional Buttons: Used to adjust power output, zoom, and navigate menus.
  • LOCK Switch: Prevents accidental changes to settings.
  • ZOOM Button: Adjusts the flash head's focal length (24-105mm).
  • FN/ACT/CH Buttons: Used for function settings, activation, and channel selection in wireless modes.

5.3 Flash Modes

The YN560 III offers several operating modes:

  • M (Manual) Mode:

    Allows manual adjustment of flash output from 1/128 to 1/1 power in 1/3 stop increments. Use the directional buttons to set the desired power level. This mode provides precise control over light output.

    Series of photos demonstrating different flash power outputs from 1/128 to 1/1

    Image 5.2: Examples of varying flash power output from 1/128 to 1/1, illustrating the range of control.

  • Multi (Stroboscopic) Mode:

    Fires a series of rapid flashes during a single exposure, useful for capturing multiple movements of a subject in one frame. Adjust flash frequency and number of flashes via the controls.

  • S1 (Optical Slave) Mode:

    The flash will fire in sync with another flash unit. It detects the first flash from a master unit and triggers simultaneously. Suitable for manual flash systems.

  • S2 (Optical Slave with Pre-flash Ignore) Mode:

    Similar to S1, but designed to ignore the pre-flash emitted by TTL (Through-The-Lens) flash systems. The YN560 III will only trigger on the main flash pulse.

  • RX (Radio Receiver) Mode:

    Activates the built-in 2.4GHz wireless receiver. This allows the YN560 III to be triggered and controlled remotely by YONGNUO RF-602, RF-603, or YN560-TX transmitters. Select the appropriate channel (CH) to match your transmitter.

5.4 Flash Head Adjustment

The flash head can be tilted and swiveled to direct light as needed.

  • Tilt: The flash head can be tilted upwards from -7 degrees to 90 degrees.
  • Swivel: The flash head can be rotated horizontally up to 270 degrees (180 degrees left, 90 degrees right).
Diagram showing the tilt and swivel range of the Yongnuo YN560 III flash head

Image 5.3: The YN560 III flash head can tilt from -7° to 90° and swivel 270° for flexible lighting angles.

5.5 Zoom Function

Press the ZOOM button to adjust the flash coverage from 24mm to 105mm. This allows you to match the flash coverage to your lens's focal length for more efficient light distribution.

5.6 Built-in Reflector and Diffuser

The flash head includes a pull-out wide-angle diffuser and a white reflection card (catchlight panel). The diffuser helps soften and spread the light, while the reflection card can be used to create catchlights in a subject's eyes when bouncing the flash.

Close-up of the Yongnuo YN560 III flash head showing the pull-out reflection board and diffuser

Image 5.4: The reflection board and diffuser integrated into the flash head for light modification.

6. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the flash unit. For stubborn dirt, use a cloth lightly dampened with water and a mild detergent, then wipe dry. Do not use organic solvents like paint thinner or benzene.
  • Battery Care: Always remove batteries when the flash is not in use for extended periods to prevent leakage. Store batteries in a cool, dry place.
  • Storage: Store the flash unit in its protective bag in a cool, dry, and well-ventilated area, away from direct sunlight and extreme temperatures.
  • Hot Shoe Contacts: Keep the hot shoe contacts clean and free of dust or debris to ensure proper communication with the camera or trigger.

7. Troubleshooting

ProblemPossible CauseSolution
Flash does not power on.Batteries are dead or incorrectly inserted.Replace batteries or reinsert them with correct polarity.
Flash does not fire.Flash not ready, incorrect mode, hot shoe connection issue, or trigger problem.Wait for the PILOT light to turn red. Check flash mode (M, S1, S2, RX). Ensure flash is securely mounted. Verify trigger settings if using RX mode.
Slow recycle time.Low battery power or high flash output.Replace batteries. Reduce flash power output.
Flash overheats.Excessive continuous firing at high power.Allow the flash to cool down. Reduce firing frequency or power output. The flash has built-in overheat protection.
Wireless triggering fails.Incorrect channel, distance, or obstructions.Ensure flash (RX mode) and transmitter are on the same channel. Check line of sight for optical modes (S1/S2). Reduce distance for radio mode (RX).

8. Specifications

FeatureDetail
ModelYN560 III
Guide NumberGN58 (ISO 100, 105mm)
Flash ModeM, Multi, S1, S2, RX
Zoom Range24, 28, 35, 50, 70, 80, 105mm
Vertical Rotation Angle-7 to 90 degrees
Horizontal Rotation Angle0 to 270 degrees
Power Supply4 x AA size batteries (Alkaline or Ni-MH)
Flash Times100-1500 times (with AA alkaline batteries)
Recycle TimeApprox. 3 seconds (with AA alkaline batteries)
Color Temperature5600K
Flash Duration1/200s - 1/20000s
Wireless Triggering Distance20-25m indoor, 10-15m outdoor (optical); up to 100m (2.4GHz radio)
Dimensions (L x W x H)21.01 x 8.99 x 8 cm (approx.)
Weight530g (without batteries)
Compatible CamerasUniversal hot shoe for Canon, Nikon, Pentax, Olympus DSLR cameras

9. Warranty & Support

9.1 Warranty Information

This YONGNUO product comes with a 1-year warranty from the date of purchase. The warranty covers manufacturing defects and malfunctions under normal use. It does not cover damage caused by misuse, accident, unauthorized modification, or improper maintenance.

Please retain your proof of purchase for warranty claims.

9.2 Customer Support

For technical assistance, troubleshooting, or warranty service, please contact your local YONGNUO distributor or the retailer where you purchased the product. You may also visit the official YONGNUO website for further support resources and contact information.

© 2026 YONGNUO. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.