Introduction
Thank you for purchasing the Lenco L-3810 Direct-Drive Turntable. This manual provides essential information for the safe and correct use of your turntable. Please read it thoroughly before use and retain it for future reference.
The Lenco L-3810 is a direct-drive turntable designed for high-fidelity audio playback and features an integrated stereo pre-amplifier, pitch control, and two-speed settings (33 and 45 RPM).
Important Safety Instructions
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
What's in the Box
Please check that all items are present and in good condition:
- L-3810 Turntable Unit
- Removable Dust Cover
- Platter
- Slip Mat
- 45 RPM Adapter
- RCA Cable
- Power Cable
- Counterweight
- Anti-skating Weight
- Headshell with Moving Magnetic Cartridge (MMC)
Setup
1. Unpacking and Placement
Carefully remove the turntable from its packaging. Place the unit on a stable, level surface away from direct sunlight, heat sources, and excessive vibration. Ensure adequate ventilation around the unit.
2. Installing the Platter and Slip Mat
- Place the metal platter onto the center spindle of the turntable. Ensure it sits securely.
- Place the felt slip mat on top of the platter.
Image: The Lenco L-3810 turntable with the platter and slip mat in place, ready for tonearm setup.
3. Installing the Dust Cover
Align the hinges of the removable dust cover with the slots at the rear of the turntable unit and gently lower it into place.
Image: The Lenco L-3810 turntable with its clear dust cover in an open position.
4. Tonearm Setup (Counterweight and Anti-skating)
- Install Counterweight: Slide the counterweight onto the rear of the tonearm with the numbers facing forward.
- Balance the Tonearm: Release the tonearm clamp. Gently move the tonearm away from its rest. Rotate the counterweight until the tonearm is perfectly balanced horizontally, floating freely.
- Set Tracking Force: While holding the counterweight steady, rotate the numbered ring on the counterweight until "0" aligns with the line on the tonearm. Then, rotate the entire counterweight (including the numbered ring) counter-clockwise to the recommended tracking force for your cartridge (typically 2-4 grams for an MMC cartridge, refer to cartridge specifications if available).
- Set Anti-skating: Attach the anti-skating weight to the small groove on the anti-skating lever. The recommended setting is usually equal to the tracking force.
Image: A detailed view of the tonearm assembly, including the cartridge, and the pitch adjustment slider.
5. Audio Connection
The L-3810 has an integrated stereo pre-amplifier. Connect the supplied RCA cable from the turntable's RCA output jacks to an available audio input on your amplifier or powered speakers. Ensure the red plug connects to the right channel (R) and the white plug to the left channel (L).
Note: If your amplifier has a dedicated "Phono" input, you may choose to bypass the turntable's internal pre-amplifier if desired, but for most setups, using the integrated pre-amplifier is convenient.
6. Power Connection
Connect the power cable to the power input on the turntable and then plug it into a suitable wall outlet.
Operation
1. Powering On/Off
Rotate the Power knob clockwise to turn the turntable ON. Rotate it counter-clockwise to turn it OFF.
Image: A close-up view of the power knob, start/stop button, and speed indicator lights on the Lenco L-3810 turntable.
2. Selecting Playback Speed
Press the 33 or 45 button to select the appropriate playback speed for your record. The corresponding indicator light will illuminate.
3. Playing a Record
- Place a record on the platter. If playing a 7-inch single, use the 45 RPM adapter.
- Ensure the correct speed (33 or 45 RPM) is selected.
- Press the START/STOP button to begin platter rotation.
- Lift the tonearm using the mechanical arm lift lever.
- Carefully position the tonearm over the desired track on the record.
- Gently lower the tonearm using the arm lift lever. The stylus will make contact with the record, and playback will begin.
Image: A hand pressing the START/STOP button on the Lenco L-3810 turntable to initiate or halt platter rotation.
Image: A user carefully positioning the tonearm over a record on the Lenco L-3810 turntable.
4. Stopping Playback
- Lift the tonearm using the mechanical arm lift lever.
- Return the tonearm to its rest and secure it with the clamp.
- Press the START/STOP button to stop platter rotation.
5. Using Pitch Control
The PITCH ADJ. slider allows you to fine-tune the playback speed. Move the slider up or down to increase or decrease the speed, respectively. This is useful for matching tempos or correcting minor speed inaccuracies.
Image: A hand adjusting the pitch control slider on the Lenco L-3810 turntable, which modifies playback speed.
6. Target Light
The TARGET LIGHT can be pulled up to illuminate the stylus and record surface, aiding in precise cueing, especially in low-light conditions. Push it down to retract.
Maintenance
1. Cleaning the Turntable
- Wipe the dust cover and turntable chassis with a soft, dry, lint-free cloth.
- Do not use abrasive cleaners, waxes, or solvents as they may damage the finish.
- Keep the dust cover closed when not in use to prevent dust accumulation.
2. Cleaning the Stylus
A dirty stylus can cause distorted sound and damage your records. Use a soft brush designed for stylus cleaning, brushing gently from back to front (in the direction of play). Never brush from side to side.
3. Cleaning Records
Regularly clean your records with a carbon fiber brush or a record cleaning solution to remove dust and static. Always brush along the grooves, not across them.
Image: A user cleaning a vinyl record on the Lenco L-3810 turntable using a specialized record brush.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power | Power cable not connected; outlet not active. | Ensure power cable is securely connected to the turntable and a working power outlet. |
| No sound or low volume | RCA cables not connected correctly; amplifier/speakers off or volume low; incorrect input selected on amplifier. | Check RCA cable connections. Ensure amplifier/speakers are powered on and volume is adequate. Select the correct input source on your amplifier. |
| Distorted sound | Dirty stylus; incorrect tracking force or anti-skating; damaged record; worn stylus. | Clean the stylus. Re-balance the tonearm and adjust tracking force/anti-skating. Inspect the record for damage. Consider replacing the stylus if worn. |
| Incorrect playback speed | Wrong speed selected; pitch control misadjusted. | Ensure the correct 33 or 45 RPM button is selected. Adjust the Pitch Control slider to fine-tune the speed. |
| Humming noise | Grounding issue; interference from other electronics. | Ensure proper grounding if your system requires it (though this model has an integrated preamp, external grounding might still be relevant for some setups). Move the turntable away from other electronic devices. |
Specifications
| Feature | Detail |
|---|---|
| Model Name | Lenco L-3810 |
| Drive Type | Direct Drive |
| Speed Settings | 33 RPM, 45 RPM |
| Cartridge Type | Moving Magnetic Cartridge (MMC) |
| Pre-amplifier | Integrated Stereo Pre-amplifier |
| Pitch Control | Yes |
| Arm Lift | Mechanical Arm Lift |
| Dust Cover | Removable Plastic Dust Cover |
| Material | Aluminum (Platter) |
| Product Dimensions | 20.47 x 16.54 x 7.28 inches |
| Item Weight | 10.66 pounds (approx. 4.84 kg) |
| Included Components | L-3810 Turntable, RCA Cable, Power Cable, Slip Mat, 45 RPM Adapter |
Warranty & Support
Warranty Information
Lenco products are manufactured to high quality standards. This product is covered by a manufacturer's warranty against defects in materials and workmanship. The specific terms and duration of the warranty may vary by region. Please refer to the warranty card included with your product or visit the official Lenco website for detailed information.
Customer Support
Should you require assistance with your Lenco L-3810 turntable, please contact Lenco customer support. Contact details can typically be found on the official Lenco website or in the documentation provided with your purchase. When contacting support, please have your model number (L-3810) and purchase information ready.
