Introduction
This manual provides instructions for the proper installation, maintenance, and care of your BLACK+DECKER WVF418 Wet and Dry Vacuum Filter. Regular filter replacement and cleaning are essential for maintaining optimal performance of your vacuum cleaner.
Compatibility
The BLACK+DECKER WVF418 filter is designed for use with the following BLACK+DECKER wet and dry vacuum models:
- CWV9610
- CWV9610D
- CWV1408
The WVF418 package contains two (2) replacement filters.

Image: Front packaging of the BLACK+DECKER WVF418 filter, indicating it contains 2 foam wet/dry replacement filters and compatibility with CWV9610D and CWV1408 models.
Installation and Replacement
To replace the filter in your BLACK+DECKER wet and dry vacuum, follow these steps:
- Power Off: Ensure your vacuum cleaner is turned off and unplugged from the power source before attempting any maintenance.
- Access Filter Compartment: Open the dust bowl or filter compartment of your vacuum cleaner according to your specific vacuum model's instructions.
- Remove Old Filter: Carefully remove the old, dirty filter. Dispose of it responsibly.
- Install New Filter(s):
- For models CWV9610 and CWV9610D, one (1) WVF418 filter is required for replacement.
- For model CWV1408, two (2) WVF418 filters are required for replacement.
- Close Compartment: Close the dust bowl or filter compartment until it clicks securely into place.
- Test: Plug in and turn on your vacuum to ensure proper operation.

Image: Side packaging of the BLACK+DECKER WVF418 filter, illustrating that model CWV1408 uses 2 filters, while CWV9610D uses 1 filter.
Operating Considerations
The filter is a critical component for your vacuum's performance. A clean and properly installed filter ensures maximum suction power and prevents dust and debris from recirculating into the air. Always operate your vacuum with a clean, undamaged filter in place.
Maintenance and Cleaning
The WVF418 filters are washable and reusable. Regular cleaning extends the life of the filter and maintains vacuum efficiency. Follow these steps for cleaning:
- Remove Filter: Follow steps 1-3 from the "Installation and Replacement" section to remove the filter(s) from your vacuum.
- Brush Off Debris: Gently tap the filter over a waste bin to remove loose dust and debris. You may use a soft brush to dislodge stubborn particles.
- Wash: Rinse the filter under running water. For thorough cleaning, you may apply a small amount of mild dish soap, gently work it into a lather, and then rinse thoroughly until the water runs clear and no soap residue remains.
- Dry Completely: Allow the filter to air dry completely before reinstallation. Do not use heat to dry the filter, as this can damage the material. Ensure the filter is completely dry to prevent mold growth and maintain proper function.
- Reinstall: Once dry, reinstall the filter(s) as described in the "Installation and Replacement" section.
It is recommended to replace filters regularly, even with cleaning, to ensure peak performance. The frequency depends on usage.
Troubleshooting
If you experience issues with your vacuum cleaner, consider the following filter-related troubleshooting steps:
- Reduced Suction Power: A clogged or dirty filter is a common cause of reduced suction. Clean or replace the filter as described in the "Maintenance and Cleaning" section.
- Dust Blowing Out of Vacuum: This indicates that the filter may be damaged, improperly installed, or severely clogged. Inspect the filter for tears or damage. Ensure it is correctly seated in the vacuum's filter compartment. If damaged, replace the filter.
- Unusual Odors: If the vacuum emits unusual odors, especially after wet use, the filter may not have dried completely, leading to mold or mildew. Clean and thoroughly dry the filter, or replace it if the odor persists.
Specifications
| Model Number | WVF418 |
| Compatible Devices | BLACK+DECKER Handheld Vacuums: CWV9610, CWV9610D, CWV1408 |
| Material | Plastic (Foam) |
| Number of Pieces | 2 (per WVF418 package) |
| Reusability | Reusable (Washable) |
| Product Dimensions (approx.) | 3.13" L x 2.13" W x 4.06" H (for a single filter) |
| Item Weight (approx.) | 0.01 ounces (for the package) |

Image: A single BLACK+DECKER WVF418 filter held in a hand, with an overlay indicating its height is approximately 1.4 inches (3 cm).
Warranty Information
This BLACK+DECKER WVF418 filter is covered by a 2-year limited warranty. For detailed information regarding warranty terms, conditions, and claims, please refer to the warranty documentation included with your original vacuum cleaner or visit the official BLACK+DECKER website.
Customer Support
For further assistance, technical support, or to purchase additional replacement parts, please visit the official BLACK+DECKER website or contact their customer service department. Always refer to your vacuum cleaner's specific model number when seeking support.
Online Support: www.blackanddecker.com