Gladen RS 165 Speed User Manual

1. Product Overview

The Gladen RS 165 Speed is a high-performance 16 cm (165 mm) component speaker system designed for superior audio reproduction in automotive environments. Developed with a focus on detail and sound perfection, this system incorporates advanced technologies to deliver dynamic and efficient sound. It features a lightweight membrane for enhanced responsiveness, a high-efficiency tweeter, and a flexible crossover network with three adjustment possibilities.

This image displays the main components of the Gladen RS 165 Speed speaker system: the 165mm woofer, a high-efficiency tweeter, and the passive crossover network. These components work together to deliver a balanced and dynamic audio experience.

2. Setup and Installation

Proper installation is crucial for optimal performance. It is recommended that installation be performed by a qualified professional.

2.1 Components Check

• 165 mm Mid-bass drivers (2 units)
• High-efficiency Tweeters (2 units)
• Passive Crossover Networks (2 units)
• Mounting hardware (screws, clips, grilles if included)

2.2 Wiring Diagram

Connect the mid-bass drivers, tweeters, and amplifier to the passive crossover network as per the diagram provided with your product packaging. Ensure correct polarity for all connections (positive to positive, negative to negative) to prevent phase issues and ensure proper sound reproduction.

2.3 Crossover Adjustment

The crossover network offers 3 adjustment possibilities for the tweeter level. Experiment with these settings to achieve the desired tonal balance for your vehicle's acoustics and personal preference. Refer to the markings on the crossover unit for specific settings.

2.4 Mounting

Securely mount the mid-bass drivers in the designated speaker locations using the provided mounting hardware. Ensure a tight seal to maximize bass response. Mount the tweeters in a location that provides optimal sound staging, typically at ear level or reflective surfaces.

3. Operating Instructions

Once installed, the Gladen RS 165 Speed system operates in conjunction with your car's audio amplifier and head unit. No direct user operation is required for the speakers themselves.

3.1 Initial Power-Up

• Before turning on your audio system, double-check all wiring connections.
• Start with the amplifier's gain settings at their minimum.
• Gradually increase the volume from your head unit.
• Listen for clear, undistorted sound.

3.2 Break-in Period

Allow a break-in period of approximately 20-30 hours of normal listening. During this time, the speaker components will loosen up, leading to improved bass response and overall sound quality.

3.3 Sound Adjustment

Use your head unit's equalizer and sound processing features to fine-tune the audio to your preference. Avoid excessive bass boost or treble settings that may lead to distortion or damage.

4. Maintenance

The Gladen RS 165 Speed speaker system requires minimal maintenance to ensure long-lasting performance.

• Cleaning: Periodically wipe the speaker grilles and surrounds with a soft, dry cloth to remove dust and debris. Avoid using harsh chemicals or abrasive cleaners.
• Inspection: Occasionally check the speaker cones and surrounds for any signs of damage or wear. Ensure all mounting screws remain tight.
• Environment: Protect the speakers from extreme temperatures, direct sunlight, and excessive moisture, which can degrade materials over time.

5. Troubleshooting

If you experience issues with your Gladen RS 165 Speed speaker system, refer to the following common problems and solutions:

• No Sound from Speakers:
  • Check all wiring connections from the amplifier to the crossover and speakers.
  • Verify the amplifier is powered on and functioning correctly.
  • Ensure the head unit is on and outputting audio.
  • Check speaker fuses if applicable.
• Distorted Sound:
  • Reduce the volume level.
  • Check amplifier gain settings; they may be set too high.
  • Ensure speaker wires are not shorting.
  • Verify the impedance of the speakers matches the amplifier's capabilities.
• Weak or No Bass:
  • Check the polarity of the mid-bass driver connections.
  • Ensure the mid-bass drivers are securely mounted and sealed in their enclosures.
  • Adjust bass settings on your head unit or amplifier.
• Harsh or Missing Treble:
  • Check tweeter connections and polarity.
  • Adjust the tweeter level setting on the passive crossover.
  • Ensure tweeters are not obstructed.

If problems persist after attempting these solutions, contact Gladen customer support or a qualified audio technician.

6. Specifications

7. Warranty Information

Gladen products are manufactured to the highest quality standards. This product is covered by a limited warranty against defects in materials and workmanship. The specific duration and terms of the warranty may vary by region and retailer. Please retain your proof of purchase for warranty claims.

The warranty typically covers manufacturing defects but does not cover damage resulting from improper installation, misuse, abuse, accidents, unauthorized modifications, or normal wear and tear. For detailed warranty terms, please refer to the documentation provided with your purchase or contact your authorized Gladen dealer.

8. Support

For technical assistance, product inquiries, or warranty support, please contact your authorized Gladen dealer or visit the official Gladen website.

Gladen Official Website: www.gladen.com

When contacting support, please have your product model number (GA-RS165speed) and proof of purchase readily available.