1. Introduction
Thank you for choosing the Fantini Cosmi EVM 10/4" T Helical Extractor Fan with Timer. This manual provides essential information for the safe installation, operation, and maintenance of your new extractor fan. Please read these instructions carefully before installation and retain them for future reference.
2. Safety Instructions
- Ensure the power supply is disconnected before installation, maintenance, or cleaning.
- Installation must be performed by a qualified electrician and in accordance with all local and national wiring regulations.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- Do not operate the fan if any part is damaged. Contact customer support for assistance.
- Ensure adequate ventilation is provided to prevent the back-flow of gases from open flues of gas or other fuel-burning appliances.
3. Package Contents
Please check the contents of the package to ensure all components are present and undamaged:
- Fantini Cosmi EVM 10/4" T Helical Extractor Fan
- Mounting Screws and Wall Plugs
- Instruction Manual
4. Setup and Installation
This section outlines the steps for installing your extractor fan. Professional installation is recommended.
4.1 Mounting Location
The fan is designed for installation on a hard surface, typically a wall or ceiling in a bathroom or utility area. Ensure the chosen location allows for proper ventilation and access for maintenance.
4.2 Electrical Connection
The fan operates on a 120 Volt power supply. Connect the fan to the mains electricity supply according to the wiring diagram provided inside the fan's terminal box. Ensure all connections are secure and insulated.
4.3 Physical Installation
- Mark the drilling points on the wall or ceiling using the fan's mounting holes as a template.
- Drill holes and insert the provided wall plugs.
- Secure the fan to the surface using the mounting screws.
- Connect the ducting (if applicable) to the fan's outlet.
The fan's package dimensions are approximately 17 x 17 x 15 cm, and it weighs 3 kg. Consider these dimensions for proper placement.
5. Operating Instructions
The EVM 10/4" T model includes an integrated timer function.
5.1 Timer Function
The timer allows the fan to continue operating for a set period after the light switch (or other trigger) is turned off. The timer duration is typically adjustable via a small potentiometer located inside the fan's casing. Consult the wiring diagram for specific adjustment instructions.
- To adjust the timer, disconnect power to the fan.
- Carefully open the fan's cover to access the timer adjustment screw.
- Use a small screwdriver to turn the potentiometer to increase or decrease the delay time.
- Close the cover and restore power to test the new setting.
6. Maintenance
Regular maintenance ensures optimal performance and longevity of your extractor fan.
6.1 Cleaning
It is recommended to clean the fan grille and impeller periodically, depending on usage and environmental conditions.
- Always disconnect the power supply before cleaning.
- Remove the front grille.
- Gently wipe the grille and impeller blades with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Ensure all parts are completely dry before reassembling and restoring power.
7. Troubleshooting
If you encounter issues with your fan, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Fan does not operate | No power supply Loose wiring connection Faulty switch | Check circuit breaker/fuse Verify wiring connections (with power off) Test the switch |
| Fan is noisy | Obstruction in impeller Loose mounting Motor issue | Disconnect power and check for obstructions Ensure fan is securely mounted Contact customer support |
| Timer not working correctly | Incorrect timer setting Wiring error | Adjust timer setting (see Section 5.1) Verify timer wiring connections |
If the problem persists after attempting these solutions, please contact customer support.
8. Specifications
| Feature | Specification |
|---|---|
| Model Number | AP0604 |
| Brand | Fantini Cosmi |
| Item Weight | 3 Kilograms |
| Surface Recommendation | Hard floor (for mounting surface) |
| Noise Level | 20 Decibels |
| Voltage | 120 Volts |
| Package Dimensions | 17 x 17 x 15 cm |
| ASIN | B00APVSI44 |
| First Available Date | January 15, 2020 |
9. Warranty and Support
For warranty information and technical support, please refer to the documentation provided at the time of purchase or contact your retailer. Keep your proof of purchase for any warranty claims.
For further assistance, please visit the official Fantini Cosmi website or contact their customer service department.