Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Newport Brass 2470-5623 Jacobean Single Handle Cold Water Dispenser. Please read all instructions carefully before beginning installation and retain this manual for future reference. Proper installation and care will ensure optimal performance and longevity of your product.
Safety Information
- Always turn off the main water supply before beginning any plumbing work.
- Wear appropriate personal protective equipment, such as safety glasses and gloves.
- If you are unsure about any part of the installation process, consult a qualified plumber.
- Ensure all connections are secure to prevent leaks.
- Do not use excessive force when tightening connections, as this can damage the product.
Setup and Installation
Tools and Materials Required:
- Adjustable wrench
- Phillips head screwdriver
- Plumber's putty or silicone sealant
- Thread seal tape (Teflon tape)
- Bucket and towels
- Drill with appropriate bit (if drilling new hole)
Installation Steps:
- Prepare the Mounting Surface: Ensure the mounting surface (countertop or sink deck) is clean and dry. If a new hole is required, drill a 1-3/8 inch (35mm) diameter hole in the desired location, ensuring adequate clearance underneath for connections.
- Install the Dispenser: Apply a thin bead of plumber's putty or silicone sealant around the base of the dispenser. Insert the dispenser shank through the mounting hole.
- Secure the Dispenser: From underneath the sink, slide the rubber washer, metal washer, and mounting nut onto the dispenser shank. Hand-tighten the mounting nut, then use an adjustable wrench to firmly secure the dispenser, ensuring it is properly aligned. Wipe away any excess sealant.
- Connect the Water Supply: Connect the cold water supply line to the dispenser's inlet. Use thread seal tape on the threaded connections and tighten with an adjustable wrench. Do not overtighten.
- Test for Leaks: Slowly turn on the main water supply. Check all connections for leaks. If leaks are detected, tighten the connections slightly until the leak stops.
- Flush the System: Allow water to run through the dispenser for a few minutes to flush out any debris from the new installation.
Figure 1: Newport Brass 2470-5623 Jacobean Cold Water Dispenser in Antique Brass Gold finish.
Figure 2: Example installation of a Newport Brass cold water dispenser (shown in silver finish) in a kitchen setting.
Operating Instructions
The Newport Brass 2470-5623 Jacobean Cold Water Dispenser features a single handle for easy operation. To dispense cold water:
- Turn On: Rotate the handle away from the body of the dispenser. The further the handle is rotated, the greater the water flow.
- Turn Off: Rotate the handle back towards the body of the dispenser until the water flow stops completely.
This dispenser is designed to provide cold water only. Ensure your water supply is connected to a cold water line.
Maintenance and Care
To maintain the finish and performance of your Newport Brass cold water dispenser, follow these care guidelines:
- Cleaning: Clean the dispenser regularly with a soft, damp cloth. For stubborn spots, use a mild soap and water solution. Rinse thoroughly and dry immediately with a soft cloth to prevent water spots.
- Avoid Harsh Cleaners: Do not use abrasive cleaners, scouring pads, ammonia-based cleaners, or any cleaners containing bleach, acids, or alcohol. These can damage the finish and void your warranty.
- Prevent Mineral Buildup: In areas with hard water, mineral deposits may accumulate. Regular cleaning helps prevent buildup. For significant buildup, a solution of white vinegar and water can be used sparingly, followed by thorough rinsing.
- Inspect Connections: Periodically check all water connections for any signs of leaks or corrosion. Address any issues promptly.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No water flow or low flow | Main water supply off; clogged aerator; kinked supply line | Ensure main water supply is on; clean or replace aerator; check supply line for obstructions. |
| Leaking at base of dispenser | Mounting nut loose; improper sealant application | Tighten mounting nut; reapply plumber's putty or silicone sealant if necessary. |
| Leaking at water supply connection | Connection loose; missing or improperly applied thread seal tape | Tighten connection; reapply thread seal tape and ensure a secure fit. |
| Water drips after turning off | Residual water in spout; worn cartridge | A few seconds of dripping is normal for some designs due to residual water. If dripping persists, contact customer support for potential cartridge replacement. |
If you encounter issues not listed here or if the suggested solutions do not resolve the problem, please contact Newport Brass customer support.
Specifications
- Brand: Newport Brass
- Model Name: 2470-5623 Jacobean
- Mounting Type: Deck Mount
- Finish Type: Polished (Antique Brass Gold)
- Material: Brass
- Color: Gold
- Number of Handles: 1
- Included Components: Handle
- Hole Count: 1
- Installation Type: Deck Mounted
- Maximum Flow Rate: 1.5 Gallons Per Minute
- Item Weight: 2 Pounds
- Product Dimensions: 3.25"D x 12"W x 216"H (Note: 216"H seems incorrect, likely a typo in source data. Please refer to product packaging for accurate height.)
Warranty Information
Newport Brass products are manufactured to the highest quality standards and are backed by a limited warranty. For detailed information regarding the warranty terms, conditions, and registration process, please refer to the warranty card included with your product or visit the official Newport Brass website. Keep your proof of purchase for warranty claims.
Customer Support
If you have any questions about your Newport Brass 2470-5623 Jacobean Cold Water Dispenser, require technical assistance, or need to order replacement parts, please contact Newport Brass customer service. Contact information can typically be found on the product packaging or on the official Newport Brass website (www.newportbrass.com).