Kichler Grand Bank Mini Pendant/Wall Light User Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Kichler Grand Bank Mini Pendant/Wall Light, Model 43189AUB. This distinctive 1-light fixture features an Auburn Stained finish and Clear Seedy Glass, designed to complement various interior styles. Please read all instructions carefully before beginning installation or use.

Figure 1: Kichler Grand Bank Mini Pendant Light (Model 43189AUB)

Safety Information

• WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
• Always disconnect power at the main circuit breaker panel or main fuse box before beginning installation or performing any maintenance.
• Consult a qualified, certified electrician if you have any doubts or questions regarding electrical wiring or installation.
• Ensure all wiring connections are secure and comply with local electrical codes.
• Use only the specified bulb type and wattage to avoid overheating or damage.
• This fixture is suitable for Indoor Use Only and Dry Locations. Do not install in damp or wet environments.

Package Contents

Verify that all components are present before discarding packaging materials.

• Kichler Grand Bank Mini Pendant/Wall Light Fixture
• Mounting Hardware (screws, wire nuts, mounting strap)
• Instruction Manual
• Note: One (1) B bulb is required and not included.

Specifications

Setup and Installation

Before you begin, ensure the power is turned off at the circuit breaker. It is recommended to have an extra person for assistance during installation, especially when lifting the fixture. Refer to the detailed instructions included in your product packaging for specific wiring diagrams and steps.

Tools and Materials Needed:

• Ladder
• Wire strippers
• Screwdriver
• Non-contact voltage tester (recommended for safety)
• Appropriate light bulb (1 x E26 base, max 60W, not included)

Installation Steps:

1. Disconnect Power: Turn off the electricity at the main circuit breaker or fuse box for the area where you are installing the fixture. Use a non-contact voltage tester to confirm the power is off.
2. Remove Old Fixture: Carefully remove any existing light fixture from the ceiling or wall junction box. Disconnect all wires.
3. Attach Mounting Bracket: Secure the new mounting bracket (included) to the junction box on your ceiling or wall using the provided screws. Ensure it is firmly attached.
4. Thread Wires: Thread the fixture wires up through the mounting box and the canopy.
5. Determine Hanging Height (Pendant Only): If installing as a pendant, determine the desired hanging height. Adjust the chain length as needed.
6. Connect Wires: Connect the fixture's ground wire to the house ground wire (usually bare copper or green). Connect the fixture's white wire to the house white wire (neutral). Connect the fixture's black wire to the house black wire (hot). Secure all connections with wire nuts.
7. Tuck Wires: Carefully tuck all excess wires into the junction box, ensuring no wires are pinched.
8. Secure Canopy: Raise the canopy to the ceiling or wall and secure it to the mounting bracket with the provided hardware.
9. Install Glass Shade: Carefully attach the clear seeded glass shade to the fixture.
10. Install Bulb: Screw in one (1) E26 base bulb (max 60W) into the socket.
11. Restore Power: Turn the electricity back on at the main circuit breaker or fuse box.

Figure 2: Kichler Grand Bank Wall Sconce Light (Model 43189AUB) - Note: This model can be installed as a mini pendant or a wall light.

Operation

Once installed and power is restored, operate your Kichler Grand Bank Mini Pendant/Wall Light using the standard wall switch connected to the fixture. This fixture is compatible with a dimmer switch, allowing you to adjust the light intensity if connected to a compatible dimmer system.

Maintenance

Cleaning:

• Always turn off the power before cleaning.
• Wipe the fixture with a soft, dry cloth.
• Do not use abrasive cleaners, solvents, or polishes as they may damage the finish.
• For the glass shade, a mild glass cleaner can be used, applied to a cloth first, not directly to the fixture.

Bulb Replacement:

• Turn off the power to the fixture at the circuit breaker.
• Allow the bulb to cool completely before touching it.
• Carefully unscrew the old bulb.
• Install a new E26 base bulb, ensuring it does not exceed 60 watts.
• Restore power to the fixture.

Troubleshooting

Warranty

This Kichler fixture comes with a 1-year warranty against manufacturer defects. Please retain your proof of purchase for warranty claims. For specific warranty details and conditions, refer to the documentation included with your product or contact Kichler customer support.

Support and Contact

For further assistance, technical support, or to inquire about replacement parts, please visit the official Kichler website or contact their customer service department. Contact information can typically be found on the product packaging or on the Kichler website.