Introduction
The Accu-Chek Nano Glucose Meter is a compact and high-performance device designed for self-testing of blood glucose levels. It offers a brilliant backlit display for easy reading, requires no coding, and provides fast results. This manual provides essential information for the safe and effective use of your Accu-Chek Nano system.
The system is intended for testing glucose in fresh capillary whole blood and is for in vitro diagnostic use only.
Safety Information
Important: Always read the Owner's Booklet thoroughly before using the Accu-Chek Nano Glucose Meter. Failure to follow instructions can lead to inaccurate results or injury.
- This device is for self-testing only.
- For in vitro diagnostic use. Do not use for diagnosis of diabetes or screening of general population.
- Keep out of reach of children.
- Dispose of used lancets and test strips according to local regulations for biohazardous waste.
Components of the System
Your Accu-Chek Nano system typically includes the following components:
- Accu-Chek Nano Blood Glucose Meter
- Accu-Chek SmartView Test Strips
- Accu-Chek FastClix Lancing Device
- Accu-Chek FastClix Lancets (preloaded in drums)
- Carrying Case
- Owner's Booklet
Image: Accu-Chek Nano Glucose Meter in its retail packaging, showcasing the meter and test strip.
Setup
- Install Battery: The Accu-Chek Nano meter uses a Lithium battery. Open the battery compartment on the back of the meter and insert the battery, ensuring correct polarity. Close the compartment securely.
- Set Time and Date: Upon first use or after battery replacement, the meter may prompt you to set the time and date. Follow the on-screen instructions using the navigation buttons.
- Prepare Lancing Device:
- Insert a new Accu-Chek FastClix lancet drum into the lancing device.
- Select the appropriate penetration depth setting for your skin type (11 customizable settings available).
- No Coding Required: The Accu-Chek Nano meter does not require manual coding, simplifying the setup process.
Operating Instructions
Follow these steps to perform a blood glucose test:
- Wash and Dry Hands: Use warm, soapy water to wash your hands thoroughly. Dry them completely.
- Insert Test Strip: Remove an Accu-Chek SmartView test strip from its vial and immediately close the vial cap tightly. Insert the metallic end of the test strip into the meter. The meter will turn on automatically.
- Obtain Blood Sample: Use the Accu-Chek FastClix lancing device to obtain a drop of blood from your fingertip. Press the lancing device firmly against the side of your fingertip and press the release button.
- Apply Blood Sample: Gently touch the tip of the test strip to the blood drop. Do not apply blood to the top of the strip. The meter will draw the blood into the strip.
- Read Result: Your blood glucose result will appear on the display in approximately 5 seconds.
- Remove and Dispose: Remove the used test strip from the meter. Dispose of the used test strip and lancet according to local regulations.
Maintenance and Care
- Cleaning: Clean the meter's exterior with a soft cloth dampened with water or a mild cleaning solution. Do not immerse the meter in liquid.
- Storage: Store the meter and test strips in a cool, dry place, away from direct sunlight and extreme temperatures. Keep test strips in their original vial with the cap tightly closed.
- Battery Replacement: Replace the battery when the low battery indicator appears on the display.
Troubleshooting
If you encounter issues with your Accu-Chek Nano meter, refer to the following common problems and solutions:
| Problem/Error Code | Possible Cause | Solution |
|---|---|---|
| E-1 (Test strip error) | Damaged or expired test strip; strip inserted incorrectly. | Insert a new, unexpired test strip correctly. Ensure the vial cap was closed tightly. |
| E-2 (Temperature error) | Meter or test strip is outside operating temperature range. | Move the meter and strips to an area within the specified operating temperature range (typically 10°C to 40°C or 50°F to 104°F) and wait 20 minutes before testing. |
| Low Battery Icon | Battery is running low. | Replace the battery immediately. |
| Inaccurate results | Improper testing technique; expired strips; meter malfunction. | Review operating instructions. Use control solution to check meter accuracy. Contact customer support if issues persist. |
For a complete list of error codes and troubleshooting steps, please refer to your Owner's Booklet.
Specifications
- Model Name: Nano
- Brand: Accu-Chek
- Product Dimensions: 6.6 x 3.9 x 5.6 inches; 8.01 ounces
- Battery Cell Composition: Lithium
- Operating Time (Test Result): 5 Seconds
- Manufacturer: Roche
- ASIN: B009Z8SO5Q
- UPC: 365702483101
- Date First Available: October 31, 2012
Warranty and Support
For detailed warranty information and customer support, please refer to the warranty card included with your product or visit the official Accu-Chek website. You can also contact Accu-Chek customer service for assistance with product inquiries, technical support, or to order replacement parts.
Online Resources: www.accu-chek.com
