1. Introduction
The Intermec SR61B is a robust, handheld bar code reader designed for industrial environments. This device provides reliable and efficient data capture for various applications, including inventory management, asset tracking, and point-of-sale operations. This manual provides essential information for the proper setup, operation, maintenance, and troubleshooting of your SR61B bar code reader.
Figure 1: Intermec SR61B Handheld Bar Code Reader. This image displays the front view of the SR61B device, highlighting its ergonomic design and scanning window.
2. Setup
2.1 Unpacking
Carefully remove all components from the packaging. Verify that all items listed in the packing slip are present. Retain the packaging for future storage or shipping.
2.2 Battery Installation
- Locate the battery compartment cover on the handle of the SR61B.
- Unscrew or unlatch the cover to open the compartment.
- Insert the provided battery, ensuring the contacts align correctly with the terminals inside the compartment.
- Replace the battery compartment cover and secure it.
2.3 Initial Charging
Before first use, fully charge the SR61B battery. Connect the device to its charging cradle or directly to a power adapter using the appropriate cable. The charging indicator light will typically illuminate during charging and change color or turn off when charging is complete.
2.4 Connecting to a Host System
The SR61B can connect to various host systems via Bluetooth or a wired connection (if applicable to your model). Refer to your host system's documentation for specific pairing or connection instructions. For Bluetooth, ensure the SR61B is in pairing mode and discoverable by the host device.
3. Operating Instructions
3.1 Powering On/Off
To power on the device, press and hold the power button (usually located on the handle or top) until the device activates. To power off, press and hold the power button again until the device shuts down.
3.2 Basic Scanning Procedure
- Ensure the SR61B is powered on and connected to your host system.
- Point the scanning window at the barcode you wish to read.
- Press and hold the trigger button. A red aiming beam or illumination will appear.
- Position the aiming beam over the entire barcode.
- Once the barcode is successfully read, the device will typically emit an audible beep and/or the indicator light will flash green.
- Release the trigger button. The scanned data will be transmitted to the host system.
3.3 Indicator Lights and Sounds
The SR61B uses various indicator lights and sounds to communicate its status:
- Green Light/Beep: Successful scan.
- Red Light: Error or low battery (may vary by configuration).
- Blue Light (flashing): Bluetooth pairing mode.
- Blue Light (solid): Bluetooth connected.
4. Maintenance
4.1 Cleaning the Device
To maintain optimal performance, keep the SR61B clean. Use a soft, lint-free cloth dampened with water or a mild, non-abrasive cleaning solution. Do not use harsh chemicals, solvents, or abrasive materials, as these can damage the device. Pay particular attention to the scanning window to ensure clear readings.
4.2 Battery Care and Storage
To prolong battery life:
- Avoid fully discharging the battery frequently.
- Store the device in a cool, dry place when not in use.
- If storing for extended periods, ensure the battery is partially charged (around 50%) to prevent deep discharge.
5. Troubleshooting
This section addresses common issues you might encounter with your SR61B bar code reader.
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not power on. | Battery is discharged or not installed correctly. | Charge the battery. Ensure the battery is properly seated in its compartment. |
| Cannot scan barcodes. | Barcode is damaged, dirty, or not within range. Scanning window is dirty. Device not connected to host. | Clean the barcode and scanning window. Ensure proper distance. Verify connection to host system. |
| No data transmitted to host. | Connection issue (Bluetooth or wired). Host application not ready. | Re-establish connection. Ensure host application is active and ready to receive input. |
| Battery life is short. | Battery is old or not fully charged. | Fully charge the battery. Consider replacing the battery if it's old and capacity has degraded. |
If these steps do not resolve the issue, please contact customer support.
6. Specifications
Below are the key specifications for the Intermec SR61B Handheld Bar Code Reader (SR61BE0C00):
- Product Dimensions: 11.1 x 9.4 x 3.5 inches
- Item Weight: 4 pounds
- Model Number: SR61BE0C00
- ASIN: B009X4S6W8
- Manufacturer: INTERMEC-INDUSTRIAL PRINTERS
- First Available: August 10, 2009
7. Warranty and Support
7.1 Warranty Information
The Intermec SR61B Handheld Bar Code Reader typically comes with a standard manufacturer's warranty covering defects in materials and workmanship. Please refer to the warranty card included with your product or visit the official Intermec website for detailed warranty terms and conditions, including duration and coverage specifics.
7.2 Customer Support
For technical assistance, service, or further inquiries, please contact Intermec customer support. Contact information can usually be found on the manufacturer's website or in the product packaging. When contacting support, please have your product model number (SR61BE0C00) and serial number ready.