1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Oxford OF690Z Heaterz Premium Adventure Heated Handlebar Grips. Designed specifically for adventure motorcycles, these grips offer enhanced comfort and control in various weather conditions. Please read this manual thoroughly before installation and use to ensure proper function and safety.
Image: Oxford OF690Z Heaterz Premium Adventure Heated Handlebar Grips, showing the ergonomic design and integrated Oxford branding.
Key features include:
- Ergonomically engineered surface structures for optimized riding performance.
- Thicker rubber in high-wear areas, rhombus tread patterns for grip, and diamond tread for maximum grip.
- Silicon cables for flexibility in cold weather and winter-grade wiring to prevent cracking.
- Bonded grip design for durability and vibration absorption.
- Angled silicone wires to prevent water ingress and corrosion.
- Five heat settings for precise temperature control.
- Intelligent heat controller with battery saving mode (shuts off if voltage drops to 10.5V).
- Easy installation with plug-and-play connectors.
2. Safety Information
Always prioritize safety during installation and operation. Failure to follow these instructions may result in damage to the product, motorcycle, or personal injury.
- Ensure the motorcycle's ignition is OFF and the battery is disconnected before beginning installation.
- Do not modify the wiring harness or components.
- Verify all connections are secure and properly insulated to prevent short circuits.
- Avoid routing cables near hot engine parts or moving components.
- Do not operate the grips if they are damaged or if any wiring is exposed.
- Monitor battery voltage, especially during prolonged use with the engine off, to prevent battery drain. The intelligent controller includes a low-voltage cut-off feature.
- Always wear appropriate riding gear, including gloves, even when using heated grips.
3. Package Contents
Verify that all components are present in the package before beginning installation:
Image: Retail packaging for Oxford Heaterz Premium Adventure Heated Grips, showing the product box.
Image: Diagram illustrating the components included in the Oxford Heaterz OF690Z package.
- Heated Grips (Left and Right) x 1 pair
- Intelligent Heat Controller x 1
- Wiring Harness (with 5A fuse) x 1
- Switch Mounting Bracket x 1
- Switch Mounting Adhesive Tape x 1
- Grip Adhesive x 1 tube
- Cable Ties (various sizes) x 4
4. Installation
This section outlines the steps for installing the Oxford OF690Z Heaterz. Basic mechanical skills are recommended. If you are unsure, consult a qualified technician.
4.1 Preparation
- Ensure the motorcycle is stable on its stand.
- Disconnect the motorcycle battery (negative terminal first).
- Remove existing handlebar grips. This may require cutting or carefully prying them off. Clean the handlebar surfaces thoroughly, removing any old adhesive or residue.
- For the throttle side, ensure the plastic throttle sleeve is smooth and free of raised fins that might interfere with the new grip. Shave down any such fins if present.
4.2 Grip Installation
- Apply a thin, even layer of the supplied grip adhesive to the clean handlebar and throttle sleeve surfaces. Work quickly as the adhesive may set fast.
- Slide the appropriate heated grip onto each side. The throttle grip is typically slightly larger in internal diameter. Ensure the grips are fully seated and oriented correctly.
- Allow the adhesive to cure according to its instructions (typically several hours) before proceeding.
4.3 Wiring the System
The Oxford Heaterz feature a simplified wiring system. Refer to the wiring diagram provided in the package contents image for visual guidance.
- Connect the wiring harness: The harness has two ring connectors for direct connection to the motorcycle battery terminals (positive and negative).
- Route the wiring harness carefully, avoiding moving parts, sharp edges, and heat sources. Secure it with the provided cable ties.
- Connect the heated grips to the wiring harness using the plug-and-play connectors. Ensure a secure connection.
- Connect the Intelligent Heat Controller to the wiring harness.
4.4 Controller Mounting
Mount the Intelligent Heat Controller in a convenient and accessible location on your handlebars.
- Attach the switch mounting bracket to your handlebars using the provided hardware.
- Secure the Intelligent Heat Controller to the bracket using the adhesive tape or other suitable method. Ensure it is firmly attached and does not obstruct other controls.
4.5 Final Checks
- Double-check all wiring connections for security and proper insulation.
- Ensure grips rotate freely on the throttle tube without binding.
- Reconnect the motorcycle battery (positive terminal first, then negative).
- Test the system before riding.
5. Operation
The Intelligent Heat Controller allows for precise temperature management.
Image: The Intelligent Heat Controller, showing the control buttons and heat level indicators.
5.1 Turning On/Off
- To turn on: Press and hold either the '+' or '-' button for approximately 2 seconds. The controller will illuminate, indicating the current heat setting.
- To turn off: Press and hold either the '+' or '-' button for approximately 2 seconds until the lights extinguish.
5.2 Adjusting Heat Settings
The controller offers five heat settings, indicated by illuminated LEDs:
- Press the '+' button to increase the heat level.
- Press the '-' button to decrease the heat level.
- Available settings: 30%, 40%, 50%, 75%, 100%.
5.3 Battery Saving Mode
The Intelligent Heat Controller features a battery saving mode. If the motorcycle's battery voltage drops below 10.5 Volts, the system will automatically shut off to prevent complete battery discharge, ensuring the motorcycle can still start.
6. Maintenance
Proper maintenance ensures the longevity and performance of your heated grips.
- Cleaning: Clean the grips and controller with a damp cloth and mild soap. Avoid harsh chemicals or abrasive cleaners.
- Inspection: Regularly inspect the grips for wear, tears, or damage. Check all wiring for fraying, cracks, or loose connections.
- Cable Management: Ensure all cables remain securely fastened and away from moving parts or heat sources. Replace cable ties if they become brittle or break.
- Storage: If storing the motorcycle for an extended period, ensure the heated grips are turned off. Consider disconnecting the battery if the motorcycle will be unused for several weeks.
7. Troubleshooting
If you encounter issues with your Oxford Heaterz, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Grips do not heat up. |
|
|
| One grip heats, the other does not. |
|
|
| Controller lights flash or system shuts off unexpectedly. |
|
|
If the problem persists after attempting these solutions, please contact Oxford customer support.
8. Specifications
Image: Diagram showing the dimensions of the Oxford heated grips.
| Feature | Detail |
|---|---|
| Model | OF690Z |
| Brand | Oxford |
| Grip Material | Rubber, Silicone |
| Total Grip Length | 132 mm |
| Grip Outer Diameter | 34 mm |
| Grip Inner Diameter (Right/Throttle) | 25.6 mm |
| Grip Inner Diameter (Left) | 22 mm |
| Voltage | 12 Volts |
| Current Draw | Under 4 Amps |
| Battery Saving Feature | Automatic shut-off at 10.5V |
| Controller Dimensions (approx.) | 52mm (width) x 49mm (height) |
| Item Weight | 510 Grams (1.12 pounds) |
| Product Dimensions | 5.91 x 3.94 x 3.94 inches (packaging) |
9. Warranty and Support
For warranty information, please refer to the documentation included with your product or visit the official Oxford Products website. For technical support or assistance with troubleshooting beyond the scope of this manual, please contact Oxford customer service.
Contact Information:
- Website: www.oxfordproducts.com
- Refer to your product packaging for specific regional contact details.