1. Introduction
This manual provides detailed instructions for the proper installation, operation, and maintenance of your Telex BTR-800 Base Station. The BTR-800 is a high-performance wireless intercom base station designed for professional communication environments, offering full-duplex communication capabilities.
The BTR-800 Base Station is engineered to facilitate clear and reliable communication with up to four compatible wireless belt packs, operating within the B3 frequency band and featuring an A5F headset jack for wired connections.
2. Safety Information
Please read and understand all safety instructions before operating the BTR-800 Base Station. Failure to follow these instructions may result in injury or damage to the equipment.
- Power Source: Use only the specified power adapter for this unit. Ensure the power supply voltage matches the requirements indicated on the unit.
- Ventilation: Do not block any ventilation openings. Ensure adequate airflow around the unit to prevent overheating.
- Moisture: Do not expose the unit to rain, moisture, or excessive humidity. Avoid placing liquids near the unit.
- Servicing: Refer all servicing to qualified service personnel. Do not attempt to open or repair the unit yourself.
- Placement: Place the unit on a stable, level surface. Avoid placing it near heat sources or in direct sunlight.
3. Product Overview
3.1. Key Features
- Full-duplex communication for seamless two-way conversations.
- Supports up to four wireless belt packs simultaneously.
- Operates within the B3 frequency band.
- Equipped with an RTS A5F headset jack for wired headset connectivity.
- Robust construction suitable for demanding professional environments.
3.2. Components
The Telex BTR-800 Base Station package typically includes:
- BTR-800 Base Station Unit
- Power Supply Unit
- Antennas (typically two)
- User Manual (this document)
4. Setup
4.1. Unpacking and Inspection
Carefully unpack all components and inspect them for any signs of damage. If any items are missing or damaged, contact your dealer immediately.
4.2. Antenna Installation
Screw the provided antennas securely into the antenna connectors located on the rear panel of the base station. Ensure they are finger-tight. For optimal performance, position the antennas vertically and ensure they are not obstructed.
4.3. Connecting Power
Connect the power supply unit to the DC input jack on the rear panel of the BTR-800 Base Station. Plug the power supply into a suitable AC outlet. Do not power on the unit until all other connections are made.
4.4. Headset Connection
If using a wired headset, plug its A5F connector into the corresponding headset jack on the front or rear panel of the base station.
4.5. Belt Pack Pairing (Synchronization)
Refer to the individual belt pack's instruction manual for specific pairing procedures. Generally, this involves setting the base station and belt pack to a pairing mode, allowing them to establish a secure wireless link. Ensure all belt packs are within range during the pairing process.
5. Operating Instructions
5.1. Powering On/Off
Press the POWER button on the front panel to turn the unit on. The power indicator light will illuminate. Press the POWER button again to turn the unit off.
5.2. Adjusting Volume
Use the dedicated volume control knobs on the front panel to adjust the audio levels for the connected headsets and belt packs. Adjust to a comfortable listening level.
5.3. Communication Modes
The BTR-800 supports full-duplex communication, allowing simultaneous speaking and listening. Specific communication modes or channels may be selected via controls on the front panel or through paired belt packs, depending on the system configuration.
5.4. Using with Belt Packs
Once belt packs are paired, users can communicate wirelessly through the base station. Ensure belt packs are charged and within the operational range of the base station for uninterrupted communication.
6. Maintenance
6.1. Cleaning
Clean the exterior of the base station with a soft, dry cloth. Do not use liquid cleaners or abrasive materials, as they may damage the finish or internal components.
6.2. Storage
When not in use for extended periods, store the unit in a cool, dry place, away from direct sunlight and extreme temperatures. Disconnect the power supply and, if possible, remove antennas.
6.3. Firmware Updates
Periodically check the Telex website for available firmware updates. Follow the instructions provided with the update package carefully to ensure proper installation and to benefit from performance enhancements or new features.
7. Troubleshooting
This section addresses common issues you might encounter with your BTR-800 Base Station.
- No Power:
Solution: Check the power cable connection to the unit and the AC outlet. Ensure the power supply is functioning correctly. - No Audio from Headset/Belt Pack:
Solution: Verify headset connection. Check volume levels on both the base station and the belt pack. Ensure belt packs are properly paired and within range. - Poor Range or Intermittent Communication:
Solution: Ensure antennas are securely attached and positioned vertically. Check for obstructions between the base station and belt packs. Minimize interference from other wireless devices. - Belt Pack Not Pairing:
Solution: Ensure both the base station and belt pack are in pairing mode. Refer to the belt pack's manual for specific pairing steps. Ensure they are within close proximity during pairing.
If problems persist after attempting these solutions, contact Telex customer support or a qualified service technician.
8. Specifications
8.1. Technical Data
- Model: BTR-800-B3R5
- Frequency Band: B3 Band
- Headset Jack Type: RTS A5F
- Communication Mode: Full-Duplex
- Belt Pack Capacity: Up to 4 simultaneous belt packs
- Power Requirement: Specific DC voltage (refer to power supply label)
- Operating Temperature: (Refer to product label for specific range)
9. Warranty and Support
9.1. Warranty Information
Telex warrants this product against defects in materials and workmanship for a period specified at the time of purchase. This warranty does not cover damage caused by misuse, unauthorized modification, accident, or neglect. Proof of purchase is required for all warranty claims. For full warranty terms and conditions, please refer to the warranty card included with your product or visit the official Telex website.
9.2. Customer Support
For technical assistance, service, or further information regarding your Telex BTR-800 Base Station, please contact your authorized Telex dealer or visit the official Telex support website. Please have your model number and serial number ready when contacting support.
