Introduction
This manual provides detailed instructions for the assembly, operation, and maintenance of your Cal Lighting BO-2372FL Tiffany Floor Lamp. This Tiffany floor lamp features an antique brass finish and stands 60 inches tall. It includes a pull chain on/off switch and is designed to accommodate two 60-watt incandescent bulbs. Please read all instructions carefully before use to ensure safe and proper operation.
Safety Information
- Always disconnect the power supply before cleaning, replacing bulbs, or performing any maintenance.
- Do not use bulbs exceeding the specified wattage (60 watts per socket).
- Ensure the lamp is placed on a stable, level surface to prevent tipping.
- Keep the lamp away from water and moisture. This product is for indoor use only.
- Do not operate the lamp with a damaged cord or plug. If damaged, contact qualified service personnel.
- Keep children and pets away from the lamp during operation and assembly.
Package Contents
Verify that all components are present before beginning assembly:
- Tiffany Lamp Shade (Glass, Multicolor)
- Lamp Pole Sections (Antique Brass Finish)
- Lamp Base (Zinc Cast, Antique Brass Finish)
- Harp and Finial (for securing the shade)
- Power Cord with Plug
Setup and Assembly
Follow these steps to assemble your floor lamp:
- Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, soft surface to prevent scratches.
- Attach Base: Screw the lowest pole section into the lamp base. Turn clockwise until securely tightened.
- Assemble Pole: Connect the remaining pole sections by screwing them together clockwise. Ensure all connections are tight to prevent wobbling.
- Attach Lamp Body: Screw the assembled pole into the lamp body (the section containing the bulb sockets and pull chain).
- Install Harp: Attach the harp (the U-shaped wire frame) to the saddle on the lamp body. Squeeze the two arms of the harp together to fit them into the saddle.
- Place Shade: Carefully place the Tiffany lamp shade onto the harp. The shade should rest on the top of the harp.
- Secure Finial: Screw the finial onto the threaded rod at the top of the harp to secure the shade in place.
- Install Bulbs: Insert two incandescent bulbs (maximum 60 watts each) into the sockets. Do not overtighten.
- Position Lamp: Place the assembled lamp in your desired location, ensuring the power cord can reach an outlet without being stretched or obstructed.
Figure 1: Fully assembled Cal Lighting BO-2372FL Tiffany Floor Lamp.
Operating Instructions
To operate your Cal Lighting BO-2372FL Tiffany Floor Lamp:
- Connect Power: Plug the lamp's power cord into a standard 120V AC electrical outlet.
- Turn On/Off: The lamp is equipped with a pull chain switch. Gently pull the chain once to turn the lamp on. Pull the chain again to turn the lamp off.
Maintenance
- Cleaning: Disconnect the lamp from the power supply before cleaning. Use a soft, dry cloth to wipe the lamp base and pole. For the glass shade, use a slightly damp cloth and mild glass cleaner if necessary, then dry immediately. Avoid abrasive cleaners or solvents.
- Bulb Replacement: Ensure the lamp is unplugged and the bulbs have cooled completely. Unscrew the old bulbs counter-clockwise and replace them with new incandescent bulbs (maximum 60 watts per socket).
- Cord Inspection: Periodically inspect the power cord for any signs of damage, fraying, or wear. If damage is found, discontinue use and seek professional repair.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not turn on. | No power to the outlet. Bulb is loose or burnt out. Pull chain switch is faulty. | Check the wall outlet with another appliance. Tighten or replace the bulb(s). Contact customer support if the switch is faulty. |
| Bulbs flicker. | Loose bulb connection. Incorrect bulb type/wattage. Faulty wiring. | Tighten the bulb(s). Ensure bulbs are 60-watt incandescent. Discontinue use and contact customer support. |
| Lamp is unstable. | Pole sections not fully tightened. Uneven surface. | Ensure all pole sections and the base are securely tightened. Move the lamp to a flat, stable surface. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | BO-2372FL |
| Brand | Cal Lighting |
| Style | Antique/Tiffany |
| Finish Type | Brass - Antique Brass |
| Base Material | Brass |
| Shade Material | Glass |
| Shade Color | Multicolor |
| Product Dimensions | 9.75"D x 18.5"W x 60"H |
| Item Weight | 9.4 Pounds |
| Light Source Type | Incandescent |
| Number of Light Sources | 2 |
| Wattage | 60 watts (per bulb) |
| Voltage | 120 Volts |
| Switch Type | Pull Chain |
| Power Source | Corded Electric |
| Indoor/Outdoor Usage | Indoor |
Warranty Information
This Cal Lighting BO-2372FL Tiffany Floor Lamp is covered by a one-year manufacturer warranty. For warranty claims or further details, please retain your proof of purchase and contact the manufacturer directly.
Customer Support
If you have any questions, require assistance with assembly, or encounter issues not covered in this manual, please contact Cal Lighting customer support. Refer to the contact information provided with your purchase or visit the official Cal Lighting website for support resources.
