FLOMEC G2S20N09GMB
Contents
FLOMEC G2S20N09GMB G2 Stainless Steel Turbine Flowmeter User Manual
Model: G2S20N09GMB | Brand: FLOMEC
1. Introduction
This user manual provides comprehensive instructions for the installation, operation, maintenance, and troubleshooting of the FLOMEC G2S20N09GMB G2 Stainless Steel Turbine Flowmeter. This industrial-grade flowmeter is designed for accurate measurement of fuel, diesel, and other petroleum-based liquids in various applications. Please read this manual thoroughly before operating the device to ensure safe and efficient use.
2. Safety Information
Always observe the following safety precautions to prevent injury and damage to the flowmeter:
- Ensure the flowmeter is installed by qualified personnel in accordance with local codes and regulations.
- Verify that the system pressure does not exceed the maximum rated pressure of 1500 PSI.
- Do not use the flowmeter with fluids incompatible with 316 stainless steel.
- Disconnect power before performing any maintenance or installation procedures.
- Wear appropriate personal protective equipment (PPE) when handling the flowmeter or working with the fluid system.
- The flowmeter is rated NEMA 4/IP44 for environmental protection; however, avoid direct exposure to extreme conditions beyond its specified temperature range (0-140 °F).
3. Product Overview
The FLOMEC G2S20N09GMB is a robust turbine flowmeter featuring a durable 316 stainless steel construction and an integrated LCD display for clear readings. It is designed for precise measurement in demanding industrial environments.

Figure 3.1: Front view of the FLOMEC G2S20N09GMB Turbine Flowmeter, showing the digital LCD display, "CALIBRATE" and "DISPLAY" buttons, and flow direction arrow. The display indicates "GL" (Gallons) and "0.00" for flow rate.

Figure 3.2: Side view of the FLOMEC G2S20N09GMB Turbine Flowmeter, highlighting the 2-inch FNPT threaded connections for integration into piping systems. The label on the side provides certification and warning information.
Key Features:
- Turbine-type flowmeter for measuring fuel, diesel, and other petroleum-based liquids.
- Female NPT threaded connections (2-inch).
- Constructed from 316 stainless steel for resistance to scaling and corrosion.
- Maximum pressure rating of 1,500 PSI.
- Meets FM, CUL, CE, EX, and ATEX standards for quality assurance.
- LCD display for clear readings.
- Powered by a 9000-hour lithium battery.
4. Installation (Setup)
4.1 Pre-Installation Checklist:
- Ensure the flowmeter model (G2S20N09GMB) is suitable for your application's flow rate (20-200 GPM) and pressure.
- Verify that the fluid is compatible with 316 stainless steel.
- Confirm that the installation site provides adequate space for the flowmeter (6.3" L x 3.3" W x 4.3" H) and future maintenance.
- Ensure the fluid is clean and free of debris. A 30-mesh strainer is recommended upstream of the flowmeter.
4.2 Mounting and Connection:
- Identify the flow direction arrow on the flowmeter body. The flowmeter must be installed with the arrow pointing in the direction of fluid flow.
- Install the flowmeter in a section of pipe that is full of liquid and free of air pockets.
- For optimal accuracy, ensure there are at least 10 pipe diameters of straight pipe upstream and 5 pipe diameters downstream of the flowmeter.
- Apply appropriate thread sealant to the 2-inch FNPT connections.
- Carefully thread the flowmeter into the piping system. Do not overtighten.
- Ensure all connections are leak-free before pressurizing the system.
5. Operation
5.1 Powering On:
The FLOMEC G2S20N09GMB is powered by an internal 9000-hour lithium battery and is designed for continuous operation. The LCD display will activate automatically when flow is detected or when a button is pressed.
5.2 Display Functions:
The LCD display shows the current flow rate and totalized volume. The unit of measurement (e.g., Gallons, Liters) can typically be cycled using the "DISPLAY" button.
- DISPLAY Button: Press to cycle through various display modes, such as current flow rate, resettable total, and cumulative total.
- CALIBRATE Button: Used for field calibration or unit adjustment. Refer to the detailed calibration procedure in the full product manual for advanced settings.
5.3 Taking Measurements:
Once installed and powered, the flowmeter will automatically begin measuring flow when fluid passes through it. The flow rate will be displayed in real-time, and the totalizer will accumulate the volume.
- Ensure steady flow for accurate readings.
- To reset the resettable total, typically press and hold the "DISPLAY" button for a few seconds until the total resets. Consult the full manual for specific reset procedures.
6. Maintenance
6.1 Cleaning:
Periodically inspect the flowmeter for external dirt or debris. Clean the exterior with a damp cloth. Do not use abrasive cleaners or solvents that could damage the display or housing.
6.2 Battery Replacement:
The flowmeter is powered by a long-life 9000-hour lithium battery. When the battery indicator on the display shows low power, or the display becomes dim, the battery will need replacement. This procedure should ideally be performed by a qualified technician to maintain the NEMA 4/IP44 rating.
- Disconnect the flowmeter from the piping system and drain any fluid.
- Carefully remove the screws securing the display housing.
- Replace the old battery with a new, equivalent 9000-hour lithium battery. Ensure correct polarity.
- Reassemble the housing, ensuring the gasket is properly seated to maintain the environmental seal. Tighten screws evenly.
7. Troubleshooting
This section addresses common issues you might encounter with your FLOMEC G2S20N09GMB flowmeter.
| Problem | Possible Cause | Solution |
|---|---|---|
| No display or dim display | Low battery; display malfunction. | Replace battery (refer to Section 6.2). If issue persists, contact support. |
| Inaccurate readings | Air in line; incorrect calibration; debris in flow path; flow rate outside range. | Ensure no air pockets. Check calibration (refer to full manual). Inspect for debris and clean. Verify flow is within 20-200 GPM. |
| No flow reading despite fluid flow | Flow direction incorrect; magnetic sensor issue; severe blockage. | Check flow direction arrow. Inspect for internal blockage. Contact support if sensor is suspected. |
| Leakage at connections | Improperly sealed threads; damaged threads. | Drain system, reapply thread sealant, and retighten connections. Inspect threads for damage. |
8. Specifications
| Parameter | Value |
|---|---|
| Model Number | G2S20N09GMB |
| Flow Rate Range | 20 - 200 GPM (Gallons Per Minute) |
| Accuracy | +/-0.75% |
| Pressure Rating | 1500 PSI |
| Connection Size | 2-inch FNPT (Female National Pipe Taper) |
| Material | 316 Stainless Steel |
| Display Type | LCD |
| Maximum Viscosity | 100 cP (Centipoise) |
| Sensor Type | Magnetic |
| Strainer Mesh Type | 30 Mesh (recommended upstream) |
| Power Source | 9000-hour Lithium Battery |
| Enclosure Type | NEMA 4 / IP44 |
| Temperature Rating | 0 - 140 °F (-18 - 60 °C) |
| Dimensions (L x W x H) | 6.3 inch x 3.3 inch x 4.3 inch (16 cm x 8.4 cm x 10.9 cm) |
| Certifications / Approvals | CE certified, FM approved, cUL Listed, EX, ATEX |
9. Warranty and Support
Warranty information for the FLOMEC G2S20N09GMB Turbine Flowmeter is typically provided with the product packaging or can be obtained directly from the manufacturer, Great Plains Industries (GPI).
For technical support, service, or to inquire about replacement parts, please contact FLOMEC or Great Plains Industries customer service. Refer to their official website or product documentation for current contact information.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.