1. Introduction
Thank you for choosing the Lampa NORDRIVE N11034 KP-7 Roller Kit. This kit is designed to facilitate the loading and unloading of long or heavy items onto your vehicle's Kargo-Plus roof bars, reducing effort and preventing damage to your vehicle. Please read this manual thoroughly before installation and use to ensure safe and correct operation.
2. Safety Information
- Always ensure the roller kit is securely attached to the roof bars before loading any items.
- Do not exceed the maximum load capacity of your roof bars or vehicle. Refer to your vehicle's owner's manual for specific limits.
- Distribute the load evenly across the roof bars.
- Regularly check all fasteners and connections for tightness, especially after driving for a short distance and periodically thereafter.
- Be aware of the increased height and width of your vehicle when loaded, especially when entering garages, car washes, or low-clearance areas.
- Always secure items to the roof bars using appropriate straps or tie-downs, even when using the roller kit for loading. The roller kit is an aid, not a primary securing device.
3. Package Contents
The Lampa NORDRIVE N11034 KP-7 Roller Kit package should contain the following components:
- 1 x Roller assembly (96 cm length)
- 2 x Mounting brackets for Kargo-Plus bars
- Necessary fasteners (bolts, washers, nuts)
- Instruction manual (this document)
If any components are missing or damaged, please contact your retailer immediately.
4. Setup and Installation
Follow these steps to correctly install the KP-7 Roller Kit onto your Kargo-Plus roof bars:
- Prepare Roof Bars: Ensure your Kargo-Plus roof bars are securely installed on your vehicle according to their own instruction manual.
- Attach Mounting Brackets: Slide the mounting brackets into the T-slot channel of the rear Kargo-Plus roof bar. Position them symmetrically, ensuring the roller will be centered.
- Insert Roller Assembly: Place the roller assembly into the mounting brackets. The ends of the roller should fit snugly into the bracket cradles.
- Secure Roller: Use the provided fasteners (bolts, washers, nuts) to secure the roller assembly to the mounting brackets. Tighten all fasteners firmly, but do not overtighten.
- Final Check: Gently pull and push on the roller assembly to ensure it is firmly attached and does not wobble. The roller should spin freely.
Figure 1: Illustration of the KP-7 Roller Kit attached to a roof bar, indicating its 96 cm length. This image demonstrates the correct positioning and dimensions of the roller kit.
5. Operating Instructions
The KP-7 Roller Kit simplifies loading and unloading. Follow these guidelines for optimal use:
- Position Vehicle: Park your vehicle on a level surface.
- Prepare Item: Ensure the item you are loading is free of sharp edges that could damage the roller or your vehicle.
- Loading: Carefully lift one end of the item and place it onto the roller. Gently push the item forward, allowing the roller to assist in sliding it onto the roof bars. Guide the item to ensure it remains centered.
- Securing: Once the item is fully on the roof bars, adjust its position for even weight distribution. Secure the item firmly to the roof bars using appropriate tie-down straps. The roller kit is for assistance during loading/unloading, not for securing cargo during transit.
- Unloading: Reverse the loading process. Carefully unstrap the item, slide it back over the roller, and lower it safely.
6. Maintenance
- Cleaning: Clean the roller and brackets periodically with mild soap and water. Rinse thoroughly and dry. Avoid harsh chemicals or abrasive cleaners.
- Inspection: Regularly inspect the roller for any signs of wear, cracks, or damage. Check the mounting brackets and all fasteners for corrosion or looseness.
- Lubrication: The roller mechanism is generally maintenance-free. If the roller does not spin smoothly, ensure it is clean and free of debris. Do not apply lubricants unless specifically recommended by the manufacturer, as this could attract dirt.
- Storage: If removing the roller kit for extended periods, store it in a clean, dry place away from direct sunlight and extreme temperatures.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Roller does not spin freely. | Debris caught in mechanism; roller or brackets damaged. | Clean the roller and its ends. Inspect for damage; replace if necessary. |
| Roller kit feels loose. | Fasteners are not tight enough. | Retighten all mounting fasteners. Ensure brackets are correctly seated in the T-slot. |
| Difficulty loading heavy items. | Item weight exceeds practical limits for manual loading; improper technique. | Ensure proper lifting technique. Consider assistance for very heavy items. Verify item is centered on the roller. |
8. Specifications
- Model: N11034
- Brand: Lampa NORDRIVE
- Compatibility: Kargo-Plus Roof Bars
- Roller Length: Approximately 96 cm
- Item Weight: 3.3 Kilograms
- Package Dimensions: 101.5 x 14.5 x 6 cm
9. Warranty and Support
Lampa products are designed for quality and durability. For specific warranty information, please refer to the documentation provided with your purchase or contact your retailer. For technical support or inquiries regarding replacement parts, please contact Lampa customer service or your authorized dealer.
Please retain your proof of purchase for warranty claims.