Introduction
This manual provides essential instructions for the safe and efficient operation, installation, and maintenance of your Oasis BTSA1SK Artesian Cook 'N Cold Bottled Water Cooler. Please read all instructions carefully before using the appliance to ensure proper function and to prevent injury or damage.
Important Safety Information
Always follow basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock, and personal injury.
- Ensure the cooler is properly grounded.
- Do not operate the cooler with a damaged cord or plug.
- Keep the power cord away from heated surfaces.
- Do not immerse the cooler, cord, or plug in water or other liquids.
- Unplug the cooler before cleaning or performing any maintenance.
- Supervise children when they are near the appliance.
- Use only bottled water suitable for water coolers.
Setup
Unpacking
Carefully remove the water cooler from its packaging. Inspect for any shipping damage. Retain packaging materials for future transport if needed.
Placement
Place the cooler on a firm, level surface. Ensure there is at least 4 inches of clearance from the back and sides of the cooler to a wall or other obstruction for proper ventilation. Avoid direct sunlight or heat sources. This model is designed for indoor use.
Image: The Oasis water cooler positioned in a kitchen environment, demonstrating suitable placement.
Initial Cleaning
Before first use, wipe down the exterior of the cooler with a soft, damp cloth. Clean the drip tray and grill with mild soap and water.
Bottle Installation
Remove the protective seal from a new water bottle. Place the bottle onto the WaterGuard system at the top of the cooler. The WaterGuard system is designed to prevent spills during bottle changes. Ensure the bottle is seated firmly.
Image: A child using the Oasis water cooler, showing a water bottle correctly installed on the top-loading system.
Power Connection
Plug the cooler into a grounded 115 Volt AC outlet. Allow the cooler to stand for at least 30 minutes before dispensing water to allow the internal components to stabilize.
Initial Water Dispensing
Before consuming, dispense at least 1 quart of water from both the cold and room temperature spouts to flush the system. This ensures any air is removed and the water lines are filled.
Operating Instructions
Your Oasis BTSA1SK cooler provides both cold and room temperature water.
Image: Dispenser area of the water cooler, highlighting the different water temperature options.
Dispensing Cold Water
Place your cup under the cold water spout. Press the cold water lever or button to dispense. Release to stop the flow.
Dispensing Room Temperature Water
Place your cup under the room temperature water spout. Press the room temperature water lever or button to dispense. Release to stop the flow.
Image: A hand operating the dispenser button to fill a cup with water.
Image: A person enjoying a glass of water dispensed from the cooler.
Adjusting Cold Water Temperature
The cold water temperature can be adjusted using the thermostat located on the back of the unit. Use a flathead screwdriver to turn the adjustment screw. Turning clockwise will make the water colder, counter-clockwise will make it warmer. Allow several hours for the temperature to stabilize after adjustment.
Maintenance
Cleaning the Drip Tray
The drip tray is removable and dishwasher safe. Regularly remove and clean the drip tray to prevent water overflow and maintain hygiene. Lift the tray out, empty any collected water, wash with mild soap and water, rinse thoroughly, and replace.
Cleaning the Exterior
Wipe the exterior surfaces with a soft, damp cloth. For stainless steel parts, use a stainless steel cleaner if necessary. Avoid abrasive cleaners or solvents that could damage the finish.
Draining the Cooler
If the cooler will not be used for an extended period or needs to be moved, it should be drained. Unplug the unit, remove the water bottle, and open the drain plug located at the back of the unit. Allow all water to drain into a suitable container. Close the drain plug before re-installing a bottle and plugging in the unit.
Sanitizing
Periodic sanitization of the water reservoirs and lines is recommended to maintain water quality. Refer to specialized water cooler cleaning kits or consult a professional for detailed sanitization procedures.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No water dispensing | Empty water bottle; Air lock; Spout clogged | Replace bottle; Dispense water from all spouts to clear air; Check for obstructions in spout. |
| Water not cold enough | Thermostat setting; Poor ventilation; Recently installed bottle | Adjust cold water thermostat; Ensure adequate clearance around unit; Allow time for cooling after bottle change. |
| Leaking | Bottle cracked or improperly seated; Drain plug loose | Replace bottle or re-seat properly; Tighten drain plug. |
| Unusual noise | Compressor operation; Unit not level; Loose components | Compressor noise is normal during cooling cycles; Ensure unit is on a level surface; Contact customer support if noise is excessive or persistent. |
Specifications
- Model: BTSA1SK STN w/WTG
- Style: Cook N' Cold
- Color: Stainless Steel and Black
- Material: Stainless Steel
- Product Dimensions: 30"D x 8"W x 6"H
- Item Weight: 36 pounds
- Voltage: 115 Volts
- Wattage: 500 watts
- Power Source: Corded Electric
- Installation Type: Countertop
- Access Location: Top
- Certification: Energy Star
Warranty Information
This product comes with a 3-year warranty. For specific terms and conditions, please refer to the warranty card included with your purchase or contact Oasis customer support.
Customer Support
For further assistance, technical support, or to inquire about replacement parts, please contact Oasis customer service. Refer to the contact information provided in your product packaging or visit the official Oasis website.
