Introduction
The Bissell Power Fresh Steam Mop, Model 1940A, is designed to provide superior steam cleaning for sealed hard floors. It effectively eliminates 99.9% of germs and bacteria using the natural power of steam, without the need for harsh chemicals. This manual provides comprehensive instructions for the setup, operation, maintenance, and troubleshooting of your steam mop.

The Bissell Power Fresh Steam Mop, ready for use.
Important Safety Instructions
Please read all instructions before using your BISSELL Power Fresh Steam Mop. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- Always connect to a properly grounded outlet.
- Unplug from outlet when not in use and before conducting maintenance or troubleshooting.
- Do not leave the steam mop unattended when plugged in.
- Do not direct steam at people, animals, or electrical outlets.
- Do not immerse in water or liquid.
- Use only as described in this manual.
- Use only manufacturer's recommended attachments.
- Do not use with damaged cord or plug.
- Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners.
- Keep cord away from heated surfaces.
- Do not use on unsealed hardwood floors.
- Do not use for space heating purposes.
- Do not use in areas where flammable or combustible liquids may be present.
- Do not use without mop pads in place.
- Do not allow to be used as a toy. Close attention is necessary when used by or near children.
Product Overview
The Bissell Power Fresh Steam Mop comes with several components designed for effective cleaning:
- Bissell Power Fresh Steam Mop Unit
- (1) Microfiber Soft Pad: Ideal for everyday cleaning on delicate surfaces.
- (1) Microfiber Scrubby Pad: Designed for tackling tougher, dried-on messes.
- (2) Spring Breeze Fragrance Discs: For a fresh, clean scent during steaming.
- Carpet Glider: Allows for refreshing carpets (not for cleaning).

All components included with your Power Fresh Steam Mop.
Setup
1. Assembling the Steam Mop
Your Power Fresh Steam Mop requires minimal assembly. Simply connect the handle to the main body until it clicks securely into place.
2. Filling the Water Tank
The water tank is located on the front of the unit. To fill:
- Remove the water tank from the unit by lifting it straight up.
- Unscrew the cap at the bottom of the water tank.
- Fill the tank with distilled or demineralized water. Do not use cleaning solutions or essential oils in the water tank.
- Replace the cap securely and place the water tank back into the unit, ensuring it clicks into place.
3. Attaching Mop Pads and Fragrance Discs
To attach a mop pad:
- Select either the soft pad or the scrubby pad based on your cleaning needs.
- Align the mop pad with the bottom of the mop head and press firmly to attach it using the hook and loop fasteners.
- (Optional) For a fresh scent, insert a Spring Breeze Fragrance Disc into the small pocket on the mop pad before attaching it.
Operating Instructions
1. Powering On and Steam Control
Once the water tank is filled and the mop pad is attached:
- Plug the power cord into a grounded electrical outlet. The SmartSet Digital Steam Control will illuminate.
- Wait approximately 30 seconds for the unit to heat up. The indicator light will stop blinking and become solid when ready.
- Press the "Steam Level" button to cycle through the three steam settings: Low, Medium, or High, depending on your cleaning task.

The SmartSet Digital Steam Control allows you to select your desired steam intensity.
2. Cleaning Floors
The Bissell Power Fresh Steam Mop is safe to use on sealed hard surfaces including hardwood, ceramic, granite & marble, and linoleum.

The steam mop is suitable for various sealed hard floor types.
To clean:
- Slowly move the steam mop back and forth over the floor surface. The steam will be released automatically.
- For sanitization, slowly pass the mop over an area using the highest steam setting for at least 15 seconds. This helps eliminate 99.9% of germs and bacteria.
- The swivel steering allows for easy maneuverability around furniture and obstacles.

The steam mop effectively kills 99.9% of germs, bacteria, and viruses on sealed hard floors.
3. Using the Flip-Down Easy Scrubber
For tough, dried-on messes or grout lines, utilize the integrated Easy Scrubber:
- Step on the flip-down scrubber lever located on the back of the mop head to deploy the scrubber bristles.
- Scrub the stubborn area with the bristles while applying steam.
- Once the mess is loosened, step on the lever again to retract the scrubber and continue mopping with the pad.

The flip-down Easy Scrubber helps power through tough messes.
4. Refreshing Carpets (with Carpet Glider)
To refresh low-pile carpets or rugs:
- Attach a clean mop pad to the mop head.
- Place the mop head into the carpet glider.
- Slowly glide the mop over the carpet surface. This is for refreshing only, not deep cleaning.
Maintenance
1. Cleaning Mop Pads
The microfiber mop pads are reusable and machine washable.
- Remove the mop pad from the mop head after each use.
- Machine wash the pads in warm water with mild detergent. Do not use bleach or fabric softeners.
- Tumble dry on low or air dry.
2. Storing Your Steam Mop
After use, unplug the unit and allow it to cool completely. Empty any remaining water from the tank. The mop can be stored upright in a closet or utility area.
Troubleshooting
If you encounter issues with your Bissell Power Fresh Steam Mop, refer to the table below for common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| No Steam | Water tank is empty. | Refill water tank. |
| No Steam | Unit not plugged in or not powered on. | Ensure unit is properly plugged into a working outlet and power button is pressed. Wait 30 seconds for heating. |
| Reduced Steam | Mineral buildup in the unit. | Use distilled or demineralized water to prevent mineral buildup. Refer to the full troubleshooting guide for descaling instructions. |
| Mop not sanitizing effectively | Not enough contact time on surface. | Slowly pass the mop over the area using the highest steam setting for at least 15 seconds. |
For more detailed troubleshooting, please refer to the official Troubleshooting Guide (PDF).
Specifications
| Feature | Detail |
|---|---|
| Brand | Bissell |
| Model Name | PowerFresh® Scrubbing & Sanitizing Steam Mop |
| Model Number | 1940A |
| Special Feature | Steam Control |
| Surface Recommendation | Floor (Sealed Hard Floors) |
| Wattage | 1500 watts |
| Item Weight | 6.2 Pounds |
| Tank Volume | 16 Fluid Ounces |
| Product Dimensions | 11.6"D x 7.1"W x 28.6"H |
| Heat Time | 30 seconds |
| Power Source | Corded Electric |
| Voltage | 100-240 Volts |
| Included Components | Steam Head Attachment, 1 Microfiber Soft Pad, 1 Microfiber Scrubby Pad, 2 Spring Breeze Fragrance Discs, Carpet Glider |
Warranty & Support
The Bissell Power Fresh Steam Mop, Model 1940A, comes with a Two-Year Limited Warranty. For warranty claims or technical support, please contact Bissell customer service.
Additional resources:
- Official User Manual (PDF): Download Here
- Troubleshooting Guide (PDF): Download Here
- For more information or to purchase accessories, visit the Bissell Store on Amazon.

Bissell proudly supports the Bissell Pet Foundation, helping to save homeless pets with every product purchase.







