Fellowes Star+ 150 Comb Binding Machine

1. Introduction

The Fellowes Star+ 150 Comb Binding Machine is designed for light-duty use in small office or home environments, providing a simple and efficient solution for creating professionally bound documents. This manual provides detailed instructions to help you get the most out of your binding machine.

Key Features:

• Manually punches up to 15 sheets of paper at a time.
• Binds up to 150 sheets with a 3/4-inch comb.
• Features an enhanced accuracy edge guide for precise document centering.
• Vertical document loader ensures consistent punch alignment.
• Built-in comb storage tray with an integrated document measurement device for convenience.

Figure 1: Fellowes Star+ 150 Comb Binding Machine in its closed, compact state.

2. Setup

Before using your Fellowes Star+ 150, ensure it is placed on a stable, flat surface. The machine is designed for easy setup and storage.

Unfolding the Machine:

1. Gently lift the top cover of the machine. The punching handle will automatically extend upwards.
2. Ensure the punching handle is fully extended and locked into place for stable operation.

Figure 2: The binding machine with its top cover open and the punching handle extended, ready for use.

3. Operating Instructions

Follow these steps to punch and bind your documents using the Fellowes Star+ 150.

3.1. Punching Documents

1. Prepare Documents: Align your paper stack neatly. The machine can punch up to 15 sheets of 80gsm (20lb) paper or 2 PVC sheets (200mic / 8mil) at a time.
2. Adjust Edge Guide: Use the adjustable edge guide to center your documents for consistent punch alignment. The vertical document loader helps ensure accuracy.
3. Insert Paper: Place the edge of your paper stack into the punching slot. Ensure the paper is flush against the edge guide.
4. Punch Holes: Firmly pull the punching handle down to punch the holes. Release the handle to return it to its original position.
5. Repeat: For larger documents, repeat the punching process in smaller batches until all pages are punched.

Figure 3: A stack of paper being inserted into the punching slot of the machine, ready for hole punching.

3.2. Binding Documents

1. Select Comb: Choose a binding comb appropriate for your document thickness. The machine can bind up to 150 sheets with a 3/4-inch comb. Use the integrated document measurement device in the comb storage tray to select the correct comb size.
2. Place Comb: Position the binding comb onto the metal fingers of the binding mechanism, ensuring the comb's teeth are facing upwards and open.
3. Open Comb: Pull the binding lever (located on the side) towards you to open the comb's teeth wide enough to accommodate your punched pages.
4. Load Pages: Carefully feed your punched documents onto the open teeth of the comb. Start with the back cover, then the pages, and finally the front cover.
5. Close Comb: Push the binding lever away from you to close the comb, securing all the pages.
6. Remove Document: Lift your newly bound document from the machine.

Figure 4: Punched pages are carefully placed onto the open teeth of the binding comb, preparing the document for final binding.

3.3. Official Product Video Guide

4. Maintenance

Regular maintenance ensures the longevity and optimal performance of your binding machine.

Emptying the Punch Waste Tray:

1. Locate the punch waste tray on the side of the machine.
2. Pull the tray out to remove accumulated paper clippings.
3. Dispose of the waste and slide the tray back into its position until it clicks securely.

5. Troubleshooting

Here are solutions to common issues you might encounter:

Paper Jam:

• If paper gets stuck during punching, try gently pulling the punching handle up and down a few times.
• Reduce the number of sheets being punched at once to prevent future jams.

Inconsistent Punch Alignment:

• Ensure the paper is firmly against the adjustable edge guide before punching.
• Verify that the vertical document loader is correctly positioned for your paper size.

Difficulty with Laminated Pages:

• Laminated pages are thicker and may require punching one sheet at a time.
• Some laminated sheets may be slightly oversized for the standard punching area; trimming might be necessary for perfect alignment.

6. Specifications

7. Warranty and Support

For warranty information, technical support, or to purchase additional supplies, please refer to the official Fellowes website or contact their customer service. Keep your purchase receipt for warranty claims.

You can find more information and support at the Fellowes Store.