KanexPro WALLM-14-BLK-2242 Adjustable Tilt Wall Mount Instruction Manual

Introduction

Thank you for choosing the KanexPro WALLM-14-BLK-2242 Adjustable Tilt Wall Mount. This manual provides essential instructions for safe and proper installation, operation, and maintenance of your wall mount. Please read this manual thoroughly before installation and retain it for future reference. This mount is designed to securely hold compatible LCD and Plasma TVs, offering a variable downward tilt for optimal viewing angles.

Safety Information

WARNING: Failure to read and follow all instructions may result in personal injury, property damage, or voiding of your warranty. The manufacturer is not liable for damage or injury caused by incorrect assembly or use.

• Ensure the mounting surface can safely support the combined weight of the mount and the display. The maximum weight capacity for this mount is 165 lbs (75 kg).
• This mount is designed for installation on wood studs or solid concrete walls. Do not install on drywall alone.
• Always use a stud finder to locate the center of wood studs.
• Use appropriate mounting hardware for your specific wall type.
• Do not overtighten screws; this may cause damage and reduce holding capacity.
• Keep children and pets away during installation.
• If you are unsure about any part of the installation process, consult a qualified professional installer.

Package Contents

Verify that all components are present and undamaged before beginning installation. If any parts are missing or defective, contact customer support.

• Wall Plate (1)
• TV Brackets (2)
• Mounting Hardware Kit (various screws, washers, spacers, anchors)
• Integrated Bubble Level (on wall plate)

Setup and Installation

Tools Required (Not Included):

• Pencil
• Phillips Head Screwdriver
• Electric Drill
• Stud Finder (for wood stud installation)
• Tape Measure
• Socket Wrench (for lag bolts)

Step 1: Wall Preparation

1. Determine the desired height for your television. The center of the TV should ideally be at eye level when seated.
2. For Wood Stud Walls: Use a stud finder to locate the edges and center of two adjacent wood studs. Mark the center of the studs. The wall plate is designed to span two standard 16-inch or 24-inch on-center studs.
3. For Solid Concrete Walls: Ensure the concrete is solid and free of cracks. Mark the desired drilling locations.

Step 2: Attach Wall Plate to Wall

1. Hold the wall plate against the wall at your marked locations. Use the integrated bubble level to ensure it is perfectly horizontal.
2. Mark the drilling points through the holes on the wall plate.
3. For Wood Stud Walls: Drill pilot holes (e.g., 7/32" or 5.5mm) into the center of the studs at the marked locations.
4. For Solid Concrete Walls: Drill holes (e.g., 3/8" or 10mm) to the appropriate depth for the concrete anchors. Insert the concrete anchors flush with the wall surface.
5. Align the wall plate with the drilled holes and secure it to the wall using the provided lag bolts and washers. Tighten firmly but do not overtighten.

Image: The KanexPro WALLM-14-BLK-2242 wall mount, showing the main wall plate with integrated level and the two vertical TV brackets attached. This view illustrates the overall structure of the mount.

Step 3: Attach TV Brackets to Television

1. Carefully place your television face down on a soft, clean surface to prevent screen damage.
2. Identify the VESA mounting holes on the back of your TV. This mount supports VESA patterns up to 750 x 450 mm.
3. Select the appropriate screws, washers, and spacers from the hardware kit that fit your TV's mounting holes. Ensure the screws are not too long, which could damage internal components.
4. Attach the two TV brackets to the back of your television. Ensure they are oriented correctly (hooks facing upwards) and are securely fastened.

Image: A technical diagram illustrating the dimensions of the KanexPro WALLM-14-BLK-2242 wall mount and its VESA compatibility range. It shows the minimum and maximum VESA measurements (58-750mm horizontally, 75-450mm vertically) and the wall plate's physical dimensions (32 inches wide x 8 7/8 inches high).

Step 4: Mount Television to Wall Plate

1. With assistance, carefully lift the television with the attached brackets.
2. Hook the top edges of the TV brackets onto the top rail of the wall plate.
3. Gently lower the TV until the brackets are fully seated on the wall plate.
4. Locate the safety screws or locking mechanisms on the bottom of the TV brackets. Secure these to prevent the TV from accidentally lifting off the mount.
5. Double-check that the TV is securely attached to the wall mount before releasing it.

Operating the Tilt Feature

The KanexPro WALLM-14-BLK-2242 features a variable tilt range of 0° to -15° downward, allowing you to adjust your viewing angle to reduce glare and improve comfort.

1. To adjust the tilt, locate the tilt adjustment knobs or levers on the sides of the TV brackets.
2. Loosen these knobs/levers slightly.
3. Carefully tilt the bottom of your television forward or backward to achieve the desired angle.
4. Once the desired tilt is set, firmly tighten the adjustment knobs/levers to secure the TV in place.

Image: A perspective view of the KanexPro WALLM-14-BLK-2242 wall mount, highlighting the adjustable vertical brackets. This image helps visualize the components involved in the tilt mechanism.

Maintenance

Regular maintenance ensures the longevity and safety of your wall mount.

• Periodically check all screws and bolts to ensure they remain tight. Retighten if necessary.
• Dust the mount with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
• Inspect the mount for any signs of wear, damage, or corrosion. If any issues are found, discontinue use and contact customer support.

Troubleshooting

If you encounter issues during or after installation, refer to the following common problems and solutions:

• TV is not level: Ensure the wall plate was installed level using the integrated bubble level. If not, remove the TV, loosen the wall plate bolts, adjust, and retighten.
• TV feels unstable: Verify all mounting screws (both to the wall and to the TV) are securely tightened. Ensure the safety screws/locking mechanisms on the TV brackets are engaged. Confirm the TV weight does not exceed the mount's capacity.
• Difficulty tilting the TV: Loosen the tilt adjustment knobs/levers on the TV brackets. If they are too tight, the tilt mechanism will be stiff. Ensure no cables are obstructing the movement.
• Missing parts: Review the 'Package Contents' section. If parts are missing, contact KanexPro customer support.

Specifications

Warranty and Support

For warranty information or technical support, please refer to the documentation included with your purchase or contact KanexPro customer service directly. Keep your purchase receipt as proof of purchase.

Contact Information: Please visit the official KanexPro website for the most current support contact details.