1. Introduction
This manual provides essential information for the safe and efficient installation, operation, and maintenance of your Hansgrohe Thermostat Ecostat Select Brausenmischer 13161400. Please read these instructions carefully before installation and retain them for future reference.
2. Safety Information
- Ensure all installation work is performed by a qualified professional.
- Observe all local plumbing and building codes.
- The water supply must be turned off before any installation or maintenance work.
- Protect the product from frost.
- Operating pressure: min. 1 bar / max. 10 bar.
- Hot water temperature at the inlet should not exceed 80°C.
3. Product Overview
The Hansgrohe Ecostat Select Brausenmischer is a wall-mounted thermostatic shower mixer designed for precise temperature control and user comfort. It features a safety stop at 40°C and an adjustable temperature limitation. The integrated shelf provides convenience.
Figure 1: Front view of the Hansgrohe Ecostat Select Thermostatic Shower Mixer. This image shows the sleek, rectangular design of the mixer with its integrated shelf, temperature control knob, and water flow control. The finish is white/chrome.
4. Installation
Tools Required: Wrench, level, measuring tape, drill (if necessary), sealant tape.
- Prepare the Installation Area: Ensure the water supply is turned off. Remove any existing fixtures. The standard connection dimension (Stichmaß) is 150 ± 12 mm.
- Install S-Connections: Attach the S-connections (included in set #95772XXX) to the wall water outlets. Ensure they are level and the correct distance apart (150 ± 12 mm). Use sealant tape on the threads.
- Mount the Mixer: Carefully place the thermostatic mixer onto the S-connections. Tighten the nuts securely, ensuring the mixer is level and flush against the wall. Do not overtighten.
- Connect Hand Shower: Connect your hand shower hose to the G 1/2 outlet at the bottom of the mixer.
- Check for Leaks: Slowly turn on the main water supply and check all connections for leaks.
- Temperature Calibration (if necessary): If the water temperature does not match the markings, refer to the operating section for calibration instructions.
Figure 2: Technical drawing showing the dimensions of the Hansgrohe Ecostat Select Thermostatic Mixer. Key dimensions include the 150 ± 12 mm center-to-center distance for wall connections, overall width of 350 mm, and depth of 130 mm. The G 1/2 connections are also indicated.
5. Operating Instructions
- Temperature Control: Rotate the right handle to adjust the water temperature. The safety stop is set at 40°C. To exceed 40°C, press the safety button and continue turning the handle.
- Water Flow Control: Rotate the left handle to turn the water on/off and adjust the flow rate.
- Ecostop Button: Press the Ecostop button to limit water consumption to approximately 10 liters per minute, promoting water efficiency.
- Temperature Limitation: The maximum temperature can be adjusted by a qualified installer during installation to prevent scalding.
6. Maintenance
Regular cleaning and maintenance will ensure the longevity and optimal performance of your Hansgrohe mixer.
- Cleaning: Clean the mixer with a soft cloth and a mild, non-abrasive cleaning agent. Avoid using cleaners containing alcohol, hydrochloric acid, formic acid, acetic acid, or phosphoric acid, as these can damage the surface.
- Filter Screens: The mixer is equipped with dirt filter screens. If the water flow significantly decreases, these screens may need cleaning. Turn off the water supply, carefully remove the mixer, clean the screens, and reassemble.
- Thermostat Cartridge: If temperature regulation becomes inconsistent, the thermostat cartridge may need servicing or replacement. This should be performed by a qualified professional.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No water or low flow | Water supply off; clogged filter screens; kinked hose. | Check water supply; clean filter screens; straighten hose. |
| Inconsistent water temperature | Thermostat cartridge issue; unbalanced hot/cold pressure. | Contact a qualified plumber to inspect/replace cartridge or check water pressure. |
| Leaks at connections | Loose connections; worn seals. | Tighten connections (do not overtighten); replace seals if necessary. |
8. Specifications
- Model: 13161400
- Brand: Hansgrohe
- Mounting Type: Wall Mount
- Finish Type: Polished
- Material: Kunststoff (Plastic) / Metal
- Color: White/Chrome
- Number of Handles: 1
- Included Components: Thermostat, S-connection set (#95772XXX)
- Installation Type: Single Hole (referring to the wall connection points)
- Operating Pressure: min. 1 bar / max. 10 bar
- Safety Stop: 40°C
- Flow Rate (Hand Shower at 3 bar): 12 l/min
- Ecostop Flow Rate: 10 l/min
- Connection Size: DN15 (G 1/2)
- Center Distance (Stichmaß): 150 ± 12 mm
- Product Dimensions: 5.08 x 13.78 x 6.02 inches (approx. 12.9 x 35 x 15.3 cm)
- Item Weight: 10.04 pounds (approx. 4.56 kg)
9. Warranty and Support
Hansgrohe products are manufactured to high-quality standards. For warranty information and customer support, please refer to the official Hansgrohe website or contact your local dealer.
You can visit the official Hansgrohe store for more information: Hansgrohe Store
For technical assistance or spare parts, please contact Hansgrohe customer service, providing your product model number (13161400).
