Conair Fabric Shaver and Lint Remover (Model CLS1)

1. Introduction

Thank you for choosing the Conair Fabric Shaver and Lint Remover, Model CLS1. This battery-operated device is designed to safely and effectively remove fuzz, lint, and pills from a wide variety of fabrics, restoring their appearance. Please read this manual thoroughly before use to ensure proper operation and maintenance.

2. Safety Information

General Safety Precautions:

• Keep out of reach of children.
• Do not use on delicate fabrics that may snag easily. Test on an inconspicuous area first.
• Ensure the shaver is turned off before cleaning or handling the blades.
• Do not immerse the unit in water or other liquids.
• Use only for its intended purpose of fabric defuzzing.

Battery Safety:

• Requires 2 AA batteries (not included).
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
• Remove batteries if the device is not used for an extended period.
• Dispose of used batteries properly according to local regulations.

3. Product Overview

The Conair Fabric Shaver is designed for ease of use and effective performance. It features a comfortable ergonomic grip and a large shaving head for efficient coverage.

Figure 1: Conair Fabric Shaver with key components labeled, including the honeycomb mesh design, 2-inch shaving surface, 3-setting distance controller, detachable fuzz collector, easy-grip handle, and battery compartment.

Key Features:

• Large 2-inch Shaving Head: For efficient coverage on various fabric surfaces.
• 3 Depth Settings: Adjustable to safely shave fuzz, pilling, and lint from different fabric types.
• Detachable Lint Catcher: For easy cleanup of collected fuzz.
• Ergonomic Grip: Provides comfortable handling during use.
• Cordless Operation: Battery-operated for portability and convenience.

4. Setup

Battery Installation:

1. Locate the battery compartment at the bottom of the handle.
2. Twist and remove the battery compartment cover.
3. Insert 2 AA batteries, ensuring correct polarity (+/-) as indicated inside the compartment.
4. Replace the battery compartment cover and twist to secure.

5. Operating Instructions

Adjusting Depth Settings:

The shaver features 3 depth settings to accommodate different fabric types and pilling levels. Rotate the shaving head cover to select the desired setting:

• Setting 1 (Lowest): For delicate fabrics or light pilling.
• Setting 2 (Medium): For general use on most fabrics.
• Setting 3 (Highest): For heavy fabrics or stubborn pills.

Figure 2: A hand demonstrates adjusting the 3-setting distance controller on the fabric shaver's head.

Using the Fabric Shaver:

1. Lay the garment or fabric flat on a hard, smooth surface. Ensure the fabric is taut to prevent snagging.
2. Select the appropriate depth setting for your fabric.
3. Slide the ON/OFF switch to the 'ON' position.
4. Gently glide the shaving head over the pilled or fuzzed area. Apply light, even pressure.
5. Move the shaver in circular motions or short, even strokes. Avoid pressing too hard or holding it in one spot for too long.
6. Periodically check the lint catcher and empty it as it fills.
7. Once finished, slide the ON/OFF switch to the 'OFF' position.

Figure 3: The fabric shaver is shown in action, gently gliding over a sweater to remove fuzz and pilling.

Figure 4: A visual comparison showing a sweatshirt with visible pilling (Before) and the same sweatshirt after treatment with the fabric shaver, appearing smooth and renewed (After).

6. Maintenance

Cleaning the Lint Catcher:

For optimal performance, empty the lint catcher regularly.

1. Ensure the shaver is turned OFF.
2. Gently slide down the detachable lint catcher located on the handle.
3. Empty the collected lint and fuzz into a waste bin.
4. Slide the lint catcher back into place until it clicks securely.

Blade Care:

The blades are sharp. Handle with care.

• To clean around the blades, carefully remove the shaving head cover by twisting it counter-clockwise.
• Use a small brush (not included) to gently remove any trapped lint or debris from the blades and the inner compartment.
• Do not touch the blades directly with your fingers.
• Replace the shaving head cover by twisting it clockwise until secure.

7. Troubleshooting

Device not turning on:

• Check if batteries are inserted correctly with proper polarity.
• Replace old batteries with new AA batteries.
• Ensure the ON/OFF switch is fully in the 'ON' position.

Poor performance/not removing fuzz:

• Empty the lint catcher if it is full.
• Clean the blades and inner compartment of any trapped lint or debris.
• Ensure the fabric is laid flat and taut.
• Adjust the depth setting to a higher level for thicker fabrics or more stubborn pills.

8. Specifications

9. Warranty Information

This item has been built to U.S. electronics specifications. It may require additional modifications or converters to be used in countries other than the U.S. and Canada. For specific warranty details, please refer to the documentation included with your purchase or contact Conair customer support.

10. Customer Support

If you have any questions or require assistance with your Conair Fabric Shaver, please visit the official Conair website or contact their customer service department. Contact information can typically be found on the product packaging or the brand's official website.