1. Introduction
This manual provides essential information for the safe and efficient operation of your Klipsch RF-82 MKII and SW-112 2.1 Speaker System. Please read these instructions thoroughly before installation and use. Retain this manual for future reference.
The Klipsch 2.1 speaker system includes two RF-82 MKII floorstanding speakers and one SW-112 powered subwoofer, designed to deliver high-fidelity audio for various applications.
Image 1.1: Klipsch RF-82 MKII and SW-112 2.1 Speaker System. This image displays the complete speaker system, including two floorstanding speakers and a subwoofer.
2. Important Safety Instructions
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
- Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
3. Setup and Connection
3.1 Unpacking
Carefully remove all components from the packaging. Inspect for any signs of damage during transit. Keep the original packaging for future transport or storage. The package includes two RF-82 MKII speakers and one SW-112 subwoofer.
3.2 Speaker Placement
Optimal placement of your speakers is crucial for sound quality.
- RF-82 MKII Speakers: Position the floorstanding speakers equidistant from your primary listening position. Angle them slightly inward (toe-in) towards the listening area for improved imaging. Keep them away from corners to avoid excessive bass buildup.
- SW-112 Subwoofer: Subwoofer placement is less critical than main speakers, but can significantly impact bass performance. Experiment with different locations in the room. Often, placing it in a corner can enhance bass output, but may also lead to "boomy" sound. A good starting point is along the front wall, near one of the main speakers.
3.3 Connections
Ensure all audio equipment is turned off before making any connections.
- Connecting RF-82 MKII Speakers: Use high-quality speaker wire to connect the RF-82 MKII speakers to your amplifier or receiver. Match the positive (+) terminal on the speaker to the positive (+) terminal on the amplifier, and the negative (-) terminal on the speaker to the negative (-) terminal on the amplifier. Ensure a secure connection.
- Connecting SW-112 Subwoofer:
- LFE Connection (Recommended): If your receiver has an LFE (Low-Frequency Effects) or Subwoofer Pre-Out, connect a single RCA cable from this output on your receiver to the "LFE IN" input on the SW-112 subwoofer.
- Stereo RCA Connection: If your receiver does not have an LFE output, connect RCA cables from the receiver's stereo pre-out (or line-out) to the "LINE IN" (Left and Right) inputs on the SW-112 subwoofer.
- Power Connection: Once all audio connections are made, connect the power cords for the SW-112 subwoofer and your amplifier/receiver to appropriate power outlets.
4. Operating Instructions
4.1 Initial Power On
After all connections are secure, power on your amplifier/receiver first, then the SW-112 subwoofer. The SW-112 has an auto-on feature that detects an audio signal.
4.2 Adjusting Subwoofer Settings (SW-112)
The SW-112 subwoofer features controls for fine-tuning its performance:
- VOLUME: Adjusts the overall output level of the subwoofer. Start with a low setting and gradually increase until the bass blends seamlessly with the main speakers.
- LOW PASS: This control sets the upper frequency limit for the subwoofer. If using an LFE connection, set this to its highest setting (or bypass if available) as your receiver will manage the crossover. For stereo RCA connections, adjust this to blend with your main speakers, typically between 80Hz and 120Hz.
- PHASE: This switch (0°/180°) helps to ensure the subwoofer's output is in phase with your main speakers. Listen to music with strong bass and switch between 0° and 180°. Choose the setting that provides the most impactful and coherent bass.
Refer to your amplifier/receiver's manual for specific settings related to speaker size (set RF-82 MKII to "Large" or "Full-Band" if possible, or "Small" with a crossover if your receiver handles bass management for them) and subwoofer output levels.
5. Maintenance
- Cleaning: Dust the speaker cabinets and grilles regularly with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
- Grilles: The grilles are removable. For critical listening, some users prefer to remove them, but they offer protection for the speaker drivers. Handle them carefully to avoid damage.
- Environment: Keep speakers away from direct sunlight, excessive heat, and moisture. Ensure adequate ventilation around the subwoofer amplifier.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No sound from speakers |
|
|
| No sound from subwoofer (SW-112) |
|
|
| Distorted or unclear sound |
|
|
| Excessive or "boomy" bass |
|
|
7. Specifications
Klipsch RF-82 MKII Floorstanding Speakers
- Model Name: RF-82 MKII
- Speaker Type: Floorstanding
- Driver Size: 8.2 Inches (Woofer)
- Connectivity: Wired
- Color: Black
Klipsch SW-112 Powered Subwoofer
- Model Name: SW-112
- Speaker Type: Powered Subwoofer
- Connectivity Technology: Wired (AUX, RCA)
- Special Feature: Bass Amplification
- Control Method: Remote
- Material: Subwoofer Cabinet (typically MDF)
- Mounting Type: Table Mount (often refers to placement on floor/stand)
- Color: Black
General System Information
- Brand: Klipsch
- System Type: 2.1 Channel Speaker System
- Audio Output Mode: Stereo or 2.1 Channels
- Recommended Uses: For computers, gaming consoles, surround sound systems, televisions
- Compatible Devices: Computers, TVs, Tablets, Smartphones, Laptops
- Power Source: Corded Electric
- Warranty Type: Limited
- GTIN/UPC: 743878098167
- ASIN: B008HR8TQ0
8. Warranty and Support
8.1 Warranty Information
Your Klipsch RF-82 MKII and SW-112 2.1 Speaker System comes with a Limited Warranty. Specific terms and duration of the warranty may vary by region and retailer. Please retain your proof of purchase for warranty claims. For detailed warranty information, refer to the warranty card included with your product or visit the official Klipsch website.
8.2 Customer Support
For technical assistance, troubleshooting beyond this manual, or service inquiries, please contact Klipsch customer support.
- Online Support: Visit the official Klipsch website for FAQs, product registration, and support resources.
- Contact Information: Refer to the contact section on the Klipsch website for phone numbers or email support in your region.
