1. Introduction
This instruction manual provides essential information for the safe and efficient installation, operation, and maintenance of the Belimo B213 2-way 1/2-inch Stainless Steel Trim Ball Valve. Please read this manual thoroughly before proceeding with any procedures to ensure proper handling and to prevent potential hazards or damage to the product and system.
2. Safety Information
Adherence to safety precautions is critical during all stages of installation, operation, and maintenance. Failure to follow these instructions may result in personal injury, property damage, or equipment malfunction.
- Ensure the system is completely depressurized and drained before attempting any installation or maintenance.
- Wear appropriate personal protective equipment (PPE) such as safety glasses and gloves.
- Installation and service should only be performed by qualified and trained personnel.
- Do not exceed the maximum pressure and temperature ratings specified for the valve.
- Avoid applying excessive force to the valve body or connections during installation.
3. Product Description and Features
The Belimo B213 is a high-quality 2-way ball valve designed for reliable flow control in various applications, including HVAC and industrial fluid systems. It features a durable construction with a 1/2-inch connection size and stainless steel trim for enhanced corrosion resistance and longevity. The valve is characterized by a flow coefficient (Cv) of 4.7, indicating its flow capacity.
Figure 1: Belimo B213 2-way 1/2-inch Stainless Steel Trim Ball Valve. This image shows the brass-colored valve body with threaded ends and a mounting base at the bottom, featuring a small chain attached.
4. Setup and Installation
Proper installation is crucial for the optimal performance and longevity of the Belimo B213 ball valve. It is recommended that installation be performed by a qualified technician.
- System Preparation: Ensure the system is completely shut down, depressurized, and drained before beginning installation.
- Pipe Cleaning: Clean the pipe ends thoroughly to remove any debris, rust, or old sealant that could interfere with a proper seal or damage the valve.
- Thread Sealant: Apply an appropriate thread sealant (e.g., PTFE tape or pipe dope) to the male pipe threads. Do not apply sealant to the first thread to prevent it from entering the valve and potentially causing blockages.
- Valve Orientation: Install the valve in the correct flow direction if indicated (though 2-way ball valves are generally bi-directional). Ensure there is sufficient space for operation and maintenance.
- Tightening: Thread the valve onto the pipe ends. Use a wrench on the valve body, not the handle or actuator mounting pad, to tighten connections. Avoid over-tightening, which can damage the valve or threads.
- Leak Check: After installation, slowly repressurize the system and carefully check all connections for leaks.
5. Operating Instructions
The Belimo B213 ball valve is designed for simple quarter-turn operation.
- Opening the Valve: Rotate the valve handle or actuator 90 degrees (a quarter-turn) until it is parallel with the pipeline. This position indicates the valve is fully open, allowing maximum flow.
- Closing the Valve: Rotate the valve handle or actuator 90 degrees (a quarter-turn) until it is perpendicular to the pipeline. This position indicates the valve is fully closed, stopping flow.
For precise flow control, the valve can be partially opened or closed, though it is primarily designed for on/off applications.
6. Maintenance
The Belimo B213 ball valve is generally considered low-maintenance. Regular inspection is recommended to ensure continued reliable operation.
- Periodic Inspection: Visually inspect the valve and connections for any signs of leaks, corrosion, or physical damage.
- Cleaning: Keep the exterior of the valve clean. Avoid using harsh chemicals that could damage the valve materials.
- Leak Detection: If a leak is detected, immediately shut down and depressurize the system. Inspect the connections and seals. Do not attempt to repair under pressure.
- Actuator Check (if applicable): If an actuator is installed, ensure it operates smoothly and is securely attached.
For internal maintenance or seal replacement, it is advisable to consult a qualified professional or Belimo technical support.
7. Troubleshooting
This section addresses common issues that may arise during the use of the Belimo B213 ball valve.
| Problem | Possible Cause | Solution |
|---|---|---|
| Valve leaks at connections | Improperly tightened connections, damaged threads, insufficient thread sealant. | Depressurize system. Re-tighten connections. If leak persists, disassemble, inspect threads, reapply sealant, and reassemble. Replace if threads are damaged. |
| Valve leaks through the stem | Damaged stem packing. | Depressurize system. Tighten packing nut slightly (if adjustable). If leak persists, stem packing may need replacement by a qualified technician. |
| Valve difficult to operate (stiff) | Debris in the ball/seat area, lack of lubrication (rare for ball valves), internal damage. | Depressurize system. Cycle the valve a few times. If stiffness persists, the valve may need to be removed and inspected for internal debris or damage. Replacement may be necessary. |
| Valve not fully opening/closing | Obstruction, actuator malfunction (if present), internal damage. | Depressurize system. Inspect for external obstructions. If using an actuator, check its power and function. Internal inspection by a professional may be required. |
If troubleshooting steps do not resolve the issue, contact Belimo technical support or a qualified service professional.
8. Specifications
| Attribute | Detail |
|---|---|
| Brand | Belimo |
| Model | B213 |
| Valve Type | 2-Way Ball Valve |
| Connection Size | 1/2 inch |
| Trim Material | Stainless Steel |
| Flow Coefficient (Cv) | 4.7 |
| ASIN | B008HOSBDO |
| UPC | 645220680139 |
| Manufacturer | Belimo |
| Package Dimensions | 27.6 x 12 x 12 inches; 3 Pounds |
| Date First Available | December 11, 2014 |
9. Warranty and Support
For detailed information regarding the warranty terms and conditions for your Belimo B213 ball valve, please refer to the official Belimo warranty statement provided with your purchase or visit the official Belimo website. For technical assistance, product inquiries, or to locate authorized service centers, please contact Belimo customer support directly.
Contact information can typically be found on the Belimo website or on the product packaging.
