1. Introduction
This manual provides instructions for the proper installation, operation, and maintenance of the Hubbell CWP26CR Commercial Grade Weatherproof Cover. This product is designed to protect electrical outlets in outdoor or damp locations, ensuring safety and prolonging the life of your electrical devices. Please read these instructions thoroughly before installation and retain them for future reference.
2. Safety Information
- WARNING: Risk of electric shock. Turn off power at the circuit breaker or fuse box before installing or servicing this product.
- Installation must be performed by a qualified electrician in accordance with all national and local electrical codes.
- Do not install this product if you are unfamiliar with electrical wiring procedures.
- Ensure all connections are secure and properly insulated.
- This cover is designed for use with single-gang electrical outlets, typically GFCI or standard receptacles.
- Do not modify the product in any way. Use only genuine Hubbell replacement parts if necessary.
3. Setup and Installation
The Hubbell CWP26CR cover features a screw-in installation type for single-gang configurations.
- Turn off power: Locate the circuit breaker or fuse controlling the outlet where the cover will be installed and turn off the power. Verify power is off using a voltage tester.
- Remove existing cover (if any): Carefully remove any existing wall plate or cover from the electrical box.
- Prepare the outlet: Ensure the outlet is properly wired and secured within the electrical box.
- Position the cover: Place the Hubbell CWP26CR weatherproof cover over the outlet, aligning the screw holes with those on the electrical box.
- Secure the cover: Insert the provided screws through the cover and into the electrical box. Tighten the screws until the cover is firmly secured against the wall, ensuring a tight seal. Do not overtighten.
- Test the cover: Open and close the cover to ensure it operates smoothly and creates a proper seal when closed.
- Restore power: Once installation is complete and verified, restore power at the circuit breaker or fuse box.
No product images are available for display. Ensure the cover is flush with the mounting surface for optimal weather protection.
4. Operating Instructions
The Hubbell CWP26CR weatherproof cover is designed for passive protection. Its primary function is to shield the electrical outlet from moisture, dust, and debris when not in use or when a plug is inserted, depending on the cover type (in-use or while-not-in-use).
- To access the outlet: Open the cover by lifting the latch or hinge mechanism.
- To protect the outlet: Ensure the cover is fully closed and latched after use or when the outlet is not in active use. This maintains the weatherproof seal.
No official product videos are available for demonstration. Always ensure the cover is securely closed to maintain its weatherproof rating.
5. Maintenance
Regular maintenance helps ensure the longevity and effectiveness of your weatherproof cover.
- Cleaning: Periodically clean the cover with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the material or finish.
- Inspection: Annually inspect the cover for any signs of damage, cracks, or deterioration of the material (Polyvinyl Chloride). Check the integrity of the seal around the edges.
- Hinge/Latch Check: Ensure the hinge operates smoothly and the latch mechanism closes securely. If the cover does not close tightly, the weatherproof seal may be compromised.
- Screw Tightness: Verify that the mounting screws remain tight. Loose screws can compromise the seal and stability of the cover.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Cover does not close securely. | Misalignment, damaged latch, debris obstructing closure. | Check alignment. Clear any debris. Inspect latch for damage; replace cover if latch is broken. |
| Water or moisture inside the cover. | Improper installation, damaged seal, cover not fully closed. | Ensure cover is fully closed. Check mounting screws for tightness. Inspect gasket/seal for damage; replace cover if seal is compromised. Reinstall if necessary. |
| Cover appears cracked or brittle. | Material degradation due to age or environmental exposure. | Replace the cover immediately to maintain weatherproof protection. |
7. Specifications
- Model Number: CWP26CR
- Brand: Hubbell
- Material: Polyvinyl Chloride (PVC)
- Color: Silver
- Finish Type: Painted
- Configuration: Single Gang
- Installation Type: Screw-In
- Switch Type Compatibility: Decorator
8. Warranty Information
Hubbell products are manufactured to high-quality standards. This product is covered by the manufacturer's standard limited warranty. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or visit the official Hubbell website. Keep your proof of purchase for warranty claims.
9. Support and Contact
If you have any questions regarding the installation, operation, or maintenance of your Hubbell CWP26CR Weatherproof Cover, please contact Hubbell customer support.
- Online Support: Visit the official Hubbell website for FAQs, product documentation, and contact forms.
- Telephone Support: Refer to the Hubbell website or product packaging for customer service phone numbers.
