Brady PTL-7-498
Brady PTL-7-498 B-498 Repositionable Vinyl Cloth Labels
Model: PTL-7-498
Introduction
This manual provides detailed instructions for the proper use, maintenance, and troubleshooting of the Brady PTL-7-498 B-498 Repositionable Vinyl Cloth Labels. These labels are designed for use with compatible Brady labeling systems, offering excellent holding power while allowing for clean removal and repositioning.
Product Overview
Key Features
- The adhesive and cloth backing offers excellent holding power, yet allow for clean removal and repositioning.
- Sticks to any clean, dry surface.
- Specially formulated topcoat for excellent print quality.
- Semi-gloss finish for crisp, clean look.
- For use with BMP 61 Labeling System, BMP 71 Label Printer (with adapter), BradyPrinter M611, TLS 2200 Thermal Labeling System, TLS-PC LINK Thermal Labeling System.
What's in the Box
- 1 x BRADY Printer Label, 1/2 In. W, Vinyl, PK500 PTL-7-498 (500 labels per roll)
A roll of white Brady B-498 Repositionable Vinyl Cloth Labels, showing the adhesive backing and the core. These labels are designed for use with compatible Brady labeling systems.
Setup
Loading Labels into Compatible Printers
The PTL-7-498 labels are designed for specific Brady labeling systems. Refer to your printer's user manual for detailed instructions on loading label rolls. General steps include:
- Ensure the printer is powered off or in a safe state for media loading.
- Open the printer's media compartment or cover.
- Carefully place the PTL-7-498 label roll onto the spindle or into the designated slot, ensuring the labels feed correctly.
- Thread the leading edge of the label material through the printer's feed mechanism as indicated by the printer's guides.
- Close the media compartment or cover securely.
- Power on the printer and allow it to calibrate, if necessary.
Operating Instructions
Printing Labels
Once the labels are loaded, configure your Brady labeling system software or printer settings for the correct label type (B-498 Vinyl Cloth) and dimensions (0.5 in H x 0.5 in W). Ensure your printer's ribbon (if applicable) is compatible and properly installed for thermal transfer printing.
- Design your label content using the printer's software.
- Select the appropriate label material and size settings.
- Perform a test print to verify print quality and alignment before printing a large batch.
- Adjust print darkness and speed as needed for optimal results.
Applying Labels
The B-498 labels feature a repositionable adhesive, allowing for adjustments after initial application. For best results:
- Ensure the application surface is clean, dry, and free of dust, oil, or other contaminants.
- Peel the printed label from its liner.
- Carefully position the label on the desired surface.
- Apply firm, even pressure across the entire label, working from the center outwards to remove any air bubbles.
- If repositioning is needed, gently peel the label off the surface. The adhesive allows for clean removal without residue, provided it has not been left for an extended period or subjected to extreme conditions.
- Reapply the label to the new position, ensuring firm pressure for adhesion.
Maintenance and Storage
Storage
To maintain the quality and adhesive properties of your Brady PTL-7-498 labels:
- Store label rolls in their original packaging in a cool, dry place, away from direct sunlight and extreme temperatures.
- Avoid exposing labels to high humidity or moisture.
- Keep labels away from chemicals or solvents that could degrade the material or adhesive.
Cleaning
The labels themselves do not require cleaning. However, ensuring the surface to which they are applied is clean and dry is crucial for optimal adhesion and repositioning performance.
Troubleshooting
| Issue | Possible Cause | Solution |
|---|---|---|
| Poor Print Quality (faded, smudged, incomplete) | Incorrect printer settings, worn printhead, incompatible ribbon, dirty printhead. | Verify printer settings match label type. Clean printhead. Replace ribbon if necessary. Adjust print darkness/speed. |
| Labels Not Adhering Properly | Surface is dirty, oily, wet, or textured. Insufficient pressure during application. | Clean and dry the application surface thoroughly. Apply firm, even pressure across the entire label. Ensure surface is suitable for adhesive labels. |
| Labels Not Repositioning Cleanly or Leaving Residue | Label left on surface for too long. Surface material reacts with adhesive. | Reposition labels shortly after initial application. Test on an inconspicuous area of the surface if concerned about residue on sensitive materials. |
| Labels Not Feeding Correctly in Printer | Incorrect loading, misaligned guides, damaged roll. | Refer to printer manual for correct loading procedure. Adjust media guides. Inspect label roll for damage. |
Specifications
| Attribute | Value |
|---|---|
| Product Dimensions | 3 x 1 x 3 inches; 1.76 ounces |
| Item Model Number | PTL-7-498 |
| Date First Available | July 23, 2010 |
| Manufacturer | Brady |
| ASIN | B003X27C1W |
| Color | White |
| Size | 0.5 in H x 0.5 in W |
| Material | Vinyl |
| Brand | Brady |
| Finish Type | Adhesive |
Support and Warranty Information
For technical support, product inquiries, or warranty information regarding your Brady PTL-7-498 labels, please contact Brady customer service directly. You can find contact details and additional resources on the official Brady website or through their Brady Store on Amazon.
Specific warranty terms and conditions for consumable products like labels may vary. Please refer to the documentation provided with your purchase or contact Brady for the most current warranty details.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.