Bburago 12046GR

Download PDF
Contents

Bburago Jaguar E Type Cabrio 1961 Scale 1:18 Model Instruction Manual

Model: 12046GR

1. Introduction

This instruction manual provides essential information for the Bburago Jaguar E Type Cabrio 1961 die-cast model, scale 1:18. This model is a detailed replica intended for display and collection. Please read this manual carefully to ensure proper handling, maintenance, and enjoyment of your model.

2. Setup and Unboxing

Upon receiving your Bburago Jaguar E Type model, carefully remove it from its packaging. The model is secured to prevent damage during transit.

  1. Unpacking: Gently remove any tape or ties securing the model within its box. Avoid pulling directly on delicate parts such as mirrors or antennas.
  2. Base Removal: If the model is attached to a display base with screws, carefully unscrew them from the underside of the base. Retain the screws and base for future display or storage if desired.
  3. Inspection: Inspect the model for any visible damage that may have occurred during shipping. Contact the retailer if any issues are found.
Bburago Jaguar E Type Cabrio 1961 Scale 1:18 model, front-side view, green with beige interior.

Image 1: Front-side view of the Bburago Jaguar E Type Cabrio 1961 model. This image shows the overall appearance of the model after unboxing, highlighting its green exterior and beige interior.

3. Operating and Interactive Features

This die-cast model features several interactive components designed to replicate the original vehicle. Handle these parts with care to prevent damage.

  • Doors: The driver and passenger doors can be opened. Gently pull the door handle outwards to open. Close by gently pushing the door until it clicks into place.
  • Hood (Bonnet): The front hood can be opened to reveal the engine compartment. Locate the small latch or seam and gently lift. Close by gently lowering until it sits flush.
  • Trunk (Boot): The rear trunk can be opened. Locate the small latch or seam and gently lift. Close by gently lowering until it sits flush.
  • Steering: The front wheels are steerable. Gently turn the steering wheel inside the cabin or directly turn the front wheels to adjust their direction. Avoid excessive force.
  • Wheels: The wheels are free-rolling. The model can be gently rolled on a flat surface.
Bburago Jaguar E Type Cabrio 1961 model with open hood and driver's side door.

Image 2: The Bburago Jaguar E Type Cabrio 1961 model with its hood and driver's side door open. This illustrates the interactive features of the model, such as the opening panels.

Bburago Jaguar E Type Cabrio 1961 model, rear-side view showing detailed interior and open trunk.

Image 3: Rear-side view of the Bburago Jaguar E Type Cabrio 1961 model, showcasing the detailed interior and the open trunk. This view highlights the craftsmanship of the model's rear section and interior details.

4. Maintenance and Care

Proper care will preserve the appearance and longevity of your die-cast model.

  • Cleaning: Dust the model regularly with a soft, dry cloth or a soft brush. For stubborn dirt, lightly dampen a cloth with water (no harsh chemicals) and gently wipe. Avoid abrasive materials.
  • Storage: Store the model in a cool, dry place away from direct sunlight to prevent paint fading and material degradation. Display cases are recommended for protection from dust and accidental damage.
  • Handling: Always handle the model by its main body. Avoid touching delicate parts like mirrors, wipers, or antennas, as they can be fragile.

5. Troubleshooting

Most issues with die-cast models are related to handling or environmental factors.

  • Stiff Moving Parts: If doors, hood, or trunk feel stiff, do not force them. A very small amount of silicone lubricant applied with a toothpick to the hinge mechanism may help, but proceed with caution to avoid staining paint.
  • Dust Accumulation: Regular dusting as described in the Maintenance section is the best prevention. For dust in crevices, use a soft brush or compressed air (held at a distance).
  • Loose Parts: If a small part becomes loose, it can often be reattached using a small amount of model-specific adhesive. Ensure the adhesive is suitable for plastic and metal without damaging paint.

6. Specifications

Brand:Bburago
Model:Jaguar E Type Cabrio 1961
Model Number:12046GR
Scale:1:18
Product Dimensions:11.81 x 4.72 x 4.72 inches (approximately)
Item Weight:1.85 pounds (approximately)
Material:Die-cast metal with plastic parts
Diagram showing the dimensions of the Bburago Jaguar E Type Cabrio 1961 model, indicating a length of approximately 7 cm (2.9 inches) for the model itself, which is likely a reference to a smaller scale or a specific part, not the 1:18 model's full length.

Image 4: A diagram illustrating the dimensions of the model. Note that the diagram might represent a different scale or specific measurement, as the 1:18 model's overall length is significantly larger than 7 cm.

7. Warranty and Support

For information regarding warranty coverage or product support, please refer to the official Bburago website or contact the retailer from whom the model was purchased. Specific warranty terms may vary by region and retailer.

© 2025 Bburago. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.