Introduction
Thank you for choosing the Mount-It! MI-1131L Slim Tilting TV Wall Mount Bracket. This manual provides essential information for the safe and proper installation, operation, and maintenance of your new TV wall mount. Please read all instructions carefully before beginning installation and retain this manual for future reference.
This wall mount is designed to securely hold most 32 to 55 inch flat panel televisions, supporting VESA patterns up to 600x400mm and a maximum weight of 165 lbs (70 kgs). Its low-profile design extends only 1.9 inches from the wall, providing a sleek and modern appearance. The tilting feature allows for optimal viewing angles and glare reduction.
Important Safety Information
WARNING: Failure to read and follow all instructions may result in personal injury, property damage, or voiding of warranty. If you have any questions, please contact Mount-It! customer service.
- Do not install into drywall alone. This mount must be installed into wood studs, concrete, or brick walls.
- Ensure the mounting surface can safely support the combined weight of the mount and the television.
- Always use a stud finder to locate the center of wood studs.
- Do not exceed the maximum weight capacity of 165 lbs (70 kgs).
- Do not overtighten screws. Overtightening can cause damage to the mount or your TV.
- Always use two people for lifting and positioning the TV.
- Keep children and pets away during installation.
Package Contents
Please verify that all parts are present and undamaged before installation. If any parts are missing or defective, contact Mount-It! customer service.
- Wall Plate Assembly (with built-in level)
- TV Bracket Arms (2x)
- Mounting Hardware Kit (various screws, washers, spacers for TV and wall)
- Instruction Manual
- Small Level (additional, if included)
- HDMI Cable (if included)
Image: Overview of the Mount-It! MI-1131L TV Wall Mount Bracket, showing the main wall plate and two TV bracket arms.
Installation Guide
This section outlines the steps for installing your TV wall mount. Ensure you have the necessary tools (pencil, drill, stud finder, Phillips head screwdriver, socket wrench) before proceeding.
Step 1: Attach TV Bracket Arms to TV
- Carefully place your TV face down on a soft, clean surface to prevent scratches.
- Identify the VESA mounting holes on the back of your TV.
- Select the appropriate screws, washers, and spacers from the hardware kit that fit your TV's VESA pattern. The mount supports VESA patterns such as 100x100, 200x200, 300x300, 400x400, and up to 600x400mm.
- Attach the two TV bracket arms to the back of your TV using the selected hardware. Ensure the arms are oriented correctly (hooks facing downwards) and are securely tightened.
Image: Illustration showing a TV with its VESA mounting points and how the bracket arms attach. This mount is compatible with TVs from 32 to 55 inches.
Image: Detailed view highlighting the 2mm thick cold-rolled steel construction, the tilt locking knob, and the safety screw mechanism on the TV bracket arms.
Step 2: Mount Wall Plate to Wall
- Determine the desired height for your TV. Mark the center of the desired location on the wall.
- Use a stud finder to locate two adjacent wood studs. Mark the center of each stud. The wall plate is designed to span two standard 16-inch on-center studs.
- Hold the wall plate against the wall, aligning its center with your marked height and the mounting holes with the stud centers. Use the built-in bubble level on the wall plate to ensure it is perfectly horizontal.
- Mark the drill holes through the wall plate onto the wall.
- Drill pilot holes into the studs at the marked locations. The size of the drill bit will depend on the lag bolts provided.
- Secure the wall plate to the wall using the lag bolts and washers provided. Tighten them firmly but do not overtighten.
Image: Technical diagram of the MI-1131L wall mount, showing the built-in level, monitor brackets with 10 degrees tilt, bracket tilt locking handle, large cable through openings, and heavy-duty cold-rolled steel construction.
Image: Diagram illustrating the VESA compliant arm brackets and the overall width (25.6 inches) and height (15.75 inches) of the mount's VESA compatibility area.
Step 3: Hang TV on Wall Plate
- With assistance, carefully lift the TV with the attached bracket arms.
- Align the hooks on the TV bracket arms with the top edge of the wall plate.
- Gently lower the TV until the bracket arms securely engage with the wall plate.
- Once the TV is hanging, locate the safety screws at the bottom of each TV bracket arm. Tighten these screws to prevent the TV from accidentally lifting off the wall plate.
Image: Close-up illustration of the safety screw bracket locking system, showing how the screw secures the TV bracket to the wall plate.
Operating Instructions
Adjusting Tilt Angle
The Mount-It! MI-1131L allows for a tilt adjustment of up to 15 degrees downwards. This feature helps reduce glare and optimize your viewing experience.
- Locate the adjustable tilting knobs on the side of each TV bracket arm.
- Loosen the knobs slightly to allow the TV to tilt.
- Carefully tilt the TV to your desired angle.
- Once the desired angle is achieved, tighten the tilting knobs firmly to secure the TV in place.
Image: Visual representation of the mount's 15-degree downward tilt capability, showing the range of motion.
Maintenance
Regular maintenance ensures the longevity and safe operation of your TV wall mount.
- Cleaning: Wipe the mount with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Periodic Checks: Periodically check all screws and bolts to ensure they remain tight. Over time, vibrations or movement can cause fasteners to loosen.
- Damage Inspection: Inspect the mount for any signs of damage or wear. If any damage is found, do not use the mount and contact customer service.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| TV is not level after installation. | Wall plate not level during installation; built-in level may be inaccurate (as noted in some reviews). | Use a separate, reliable spirit level during wall plate installation. If already installed, you may need to slightly adjust the wall plate or use shims if minor. |
| TV feels unstable on the mount. | Screws not tightened sufficiently; incorrect VESA screws used; safety screws not engaged. | Ensure all screws (TV bracket to TV, wall plate to wall, safety screws) are securely tightened. Verify correct VESA screw length and type for your TV. |
| Cannot tilt the TV. | Tilting knobs are too tight. | Loosen the tilting knobs on the TV bracket arms to allow movement. Re-tighten once desired angle is set. |
| Missing parts from package. | Packaging error. | Contact Mount-It! customer service immediately for replacement parts. |
Specifications
| Model Number | MI-1131L |
| Material | Heavy-duty Cold Rolled Steel (Iron) |
| Color | Black |
| TV Size Compatibility | 32 - 55 inches |
| VESA Compatibility | 100x100mm, 200x200mm, 300x300mm, 400x400mm, 600x400mm |
| Weight Capacity | 165 lbs (70 kgs) |
| Tilt Angle | 0 to -15 degrees (downward) |
| Profile from Wall | 1.9 inches |
| Product Dimensions (Wall Plate) | 29.5 x 2 x 9.8 inches (approximate) |
| Item Weight | 6.34 pounds |
Image: Diagram showing the overall dimensions of the wall mount: 28.75 inches width, 9.5 inches height (wall plate), and 16.5 inches height (with arms extended).
Warranty and Support
Warranty Information
Mount-It! products are designed for durability and performance. For specific warranty details regarding your MI-1131L TV wall mount, please refer to the warranty card included in your package or visit the official Mount-It! website.
Customer Support
If you encounter any issues during installation or operation, or if you have questions about your product, please contact Mount-It! customer support. Our team is available to assist you.
- Website: Visit the Mount-It! Store on Amazon
- Contact: Refer to the Mount-It! website for current contact methods (phone, email, chat).
