1. Introduction
This manual provides essential instructions for the proper setup, operation, and maintenance of your DW DWSMRKC1515 Rack 1.5-Inch Clamp. Designed for percussion instruments, this clamp facilitates secure mounting of various components to a 1.5-inch rack system. Please read this manual thoroughly before use to ensure optimal performance and longevity of the product.
2. Setup
2.1 Unpacking
- Carefully remove the DW DWSMRKC1515 Rack 1.5-Inch Clamp from its packaging.
- Inspect the clamp for any signs of damage that may have occurred during shipping. If damage is found, contact your retailer immediately.
- Retain all packaging materials for future transport or storage.
2.2 Installation
The DW DWSMRKC1515 Rack 1.5-Inch Clamp is designed for straightforward installation onto standard 1.5-inch diameter rack tubing. Ensure all adjustments are made with the clamp securely fastened to prevent slippage.
Figure 1: The DW DWSMRKC1515 Rack 1.5-Inch Clamp. This image displays the clamp's robust construction, featuring two adjustable jaws with T-handle tension screws for secure attachment to rack bars and other drum hardware.
Figure 2: Dimensions of the DW DWSMRKC1515 Rack 1.5-Inch Clamp. This image illustrates the compact size of the clamp, shown in a hand for scale, with measurements indicating a height of approximately 3.2 inches (8 cm).
- Identify the desired location on your 1.5-inch diameter rack tubing where the clamp will be installed.
- Loosen the T-handle tension screws on both sides of the clamp by turning them counter-clockwise until the jaws open sufficiently to fit around the rack tubing.
- Position the clamp around the rack tubing.
- Hand-tighten both T-handle tension screws by turning them clockwise until the clamp is snug against the tubing.
- Ensure the clamp is level and in the correct orientation before fully tightening.
- Apply firm, even pressure to both T-handle tension screws to secure the clamp firmly in place. Do not overtighten, as this can damage the rack tubing or the clamp.
- Attach your desired drum hardware (e.g., cymbal arms, tom mounts) to the open end of the clamp, securing it with its respective fastening mechanism.
3. Operating
Once installed, the DW DWSMRKC1515 Rack 1.5-Inch Clamp provides a stable mounting point for various drum and percussion accessories. Its dual-jaw design allows for versatile positioning and secure attachment.
- Adjusting Position: To reposition the clamp, slightly loosen the T-handle tension screws, adjust the clamp to the new desired location, and then re-tighten firmly.
- Attaching Accessories: The secondary opening on the clamp is designed to accept standard drum hardware posts or arms. Insert the accessory and secure it using its integrated tightening mechanism.
- Stability Check: Periodically check the tightness of all screws and bolts to ensure maximum stability during use. Vibrations from playing can sometimes cause fasteners to loosen over time.
4. Maintenance
Regular maintenance will help preserve the functionality and appearance of your DW DWSMRKC1515 Rack 1.5-Inch Clamp.
- Cleaning: Wipe the clamp with a soft, dry cloth to remove dust and fingerprints. For more stubborn grime, a slightly damp cloth can be used, followed by immediate drying. Avoid abrasive cleaners or solvents.
- Lubrication: Occasionally, a small amount of light machine oil can be applied to the threads of the T-handle tension screws to ensure smooth operation.
- Inspection: Regularly inspect the clamp for any signs of wear, bending, or cracking. Ensure all moving parts operate smoothly.
- Storage: When not in use, store the clamp in a dry environment to prevent corrosion.
5. Troubleshooting
This section addresses common issues you might encounter with your DW DWSMRKC1515 Rack 1.5-Inch Clamp.
| Problem | Possible Cause | Solution |
|---|---|---|
| Clamp slips on rack tubing | Not tightened sufficiently; incorrect tubing size; worn internal gripping surfaces. | Ensure T-handle screws are fully tightened. Verify rack tubing diameter is 1.5 inches. If worn, consider replacement. |
| T-handle screws are stiff or difficult to turn | Lack of lubrication; dirt or debris in threads. | Apply a small amount of light machine oil to the screw threads. Clean any visible debris. |
| Accessory attached to clamp is unstable | Accessory not properly secured to the clamp; clamp itself is loose on the rack. | Ensure the accessory's fastening mechanism is fully tightened. Re-check the tightness of the clamp on the rack tubing. |
6. Specifications
Key technical specifications for the DW DWSMRKC1515 Rack 1.5-Inch Clamp:
| Feature | Detail |
|---|---|
| Brand | DW |
| Model Number | DWSMRKC1515 |
| Product Type | Percussion Instrument Clamp |
| Compatible Rack Tubing Diameter | 1.5 inches |
| Color | Chrome |
| Item Dimensions (L x W x H) | 10 x 6 x 4 inches |
| Item Weight | 1.3 pounds |
| Tensile Strength | 5000 PSI |
| UPC | 647139162072 |
| Manufacturer | DW - NIS Code |
| Country of Origin | Taiwan |
7. Warranty and Support
For detailed warranty information regarding your DW DWSMRKC1515 Rack 1.5-Inch Clamp, please refer to the official DW Drums website or the warranty card included with your purchase. Warranty terms and conditions may vary by region and retailer.
For technical support, replacement parts, or further assistance, please contact DW Drums customer service directly or visit their official website. You can also find more information and products from DW by visiting the DW Store on Amazon.