Introduction
Thank you for choosing the Artemide Tizio Table Lamp. Designed by Richard Sapper, this iconic lamp is renowned for its innovative counterweight system and adjustable design, providing precise illumination for various tasks. This manual provides essential information for the safe and efficient setup, operation, and maintenance of your Tizio lamp.
Safety Information
Please read all safety instructions carefully before using the lamp. Retain this manual for future reference.
- Electrical Safety: Always unplug the lamp from the power outlet before cleaning, performing maintenance, or replacing the bulb. Do not operate the lamp with a damaged cord or plug.
- Heat Warning: The halogen bulb and surrounding lamp head can become very hot during operation. Avoid touching these parts while the lamp is on or immediately after turning it off. Allow sufficient time for cooling.
- Correct Bulb Type: Use only the specified bulb type (GY6.35, 35W Halogen). Using an incorrect bulb may cause overheating or damage to the lamp.
- Indoor Use Only: This lamp is designed for indoor use in dry locations. Do not expose it to water or high humidity.
- Stable Placement: Ensure the lamp base is placed on a stable, level surface to prevent tipping.
- Ventilation: Do not cover the lamp head or bulb, as this can lead to overheating. Ensure adequate air circulation around the lamp.
Package Contents
Please verify that all components are present and undamaged upon unpacking:
- Artemide Tizio Table Lamp Unit (Base, Arms, Lamp Head)
- Halogen Bulb (GY6.35, 35W)
- Power Cord
- Instruction Manual
Setup
Assembly
The Artemide Tizio lamp typically comes pre-assembled or requires minimal setup. Follow these steps for initial preparation:
- Carefully remove all packaging materials from the lamp.
- Place the lamp base on a stable, flat surface where you intend to use it.
- If the halogen bulb is not pre-installed, gently insert the GY6.35 bulb into its socket in the lamp head. Avoid touching the glass part of the bulb with bare hands, as oils can reduce bulb life. Use a clean cloth or glove.
- Connect the power cord to the lamp base and then plug it into a standard electrical outlet.
Image: Detailed view of the lamp's articulated structure, highlighting the base and arm connections.
Placement
Position the lamp on a desk, table, or other appropriate surface. Ensure there is enough space for the arms to extend and adjust freely without obstruction. The lamp's balanced design allows for a wide range of motion.
Image: Multiple Tizio lamps demonstrating their adjustable nature and various configurations.
Operating Instructions
Power On/Off
The Artemide Tizio lamp features a touch-sensitive switch, typically located on the base or a discreet part of the arm. Gently touch the designated area to turn the lamp on or off.
Adjusting the Lamp
The lamp's signature feature is its fully adjustable, balanced electrical conductor arms. These arms allow you to effortlessly position the lamp head to direct light precisely where needed. The lamp head also features an adjustable shade for further light control.
- Gently grasp the lamp head or the arms to move them into the desired position. The counterweight system will hold the lamp in place.
- The lamp head can be tilted and rotated to fine-tune the direction of light.
Image: The Tizio lamp positioned with its arms extended, illustrating its flexibility for directing light.
Maintenance
Cleaning
To maintain the appearance and functionality of your lamp:
- Always unplug the lamp before cleaning.
- Use a soft, dry cloth to wipe down the lamp's surfaces.
- Avoid using abrasive cleaners, solvents, or polishes, as these can damage the finish.
- For the glass lens, a slightly damp cloth can be used, followed by a dry cloth to prevent streaks.
Bulb Replacement
When the bulb needs replacement:
- Ensure the lamp is unplugged and has completely cooled down.
- Carefully remove the protective glass lens or cover from the lamp head, if applicable.
- Gently pull out the old GY6.35 halogen bulb from its socket.
- Insert a new GY6.35, 35W halogen bulb. Remember to handle the new bulb with a clean cloth or glove to avoid leaving fingerprints, which can shorten bulb life.
- Replace the protective glass lens or cover.
- Plug the lamp back in and test its operation.
Troubleshooting
If you encounter issues with your Artemide Tizio Table Lamp, refer to the following table:
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not turn on. | No power, faulty bulb, or switch issue. | Ensure the lamp is securely plugged in. Check if the outlet is functional. Replace the bulb. If the issue persists, contact support. |
| Lamp gets very hot. | Normal operation for halogen bulbs, or incorrect bulb wattage. | Halogen bulbs naturally produce significant heat. Ensure proper ventilation and do not touch the lamp head when hot. Verify you are using a 35W GY6.35 bulb. |
| Light is dim or flickers. | Aging bulb, loose connection, or dirty reflector. | Replace the bulb. Check the bulb's connection in the socket. Clean the inner high-efficiency anodized aluminum reflector with a soft, dry cloth. |
| Arms do not hold position. | Wear in the counterweight mechanism. | This is rare for a properly maintained lamp. Ensure all pivot points are clean. If the issue persists, contact Artemide customer service for assistance. |
Specifications
| Feature | Detail |
|---|---|
| Brand | Artemide |
| Model | Tizio Table Lamp (Model: USC-A005015) |
| Design | Richard Sapper |
| Lamp Type | Table Lamp |
| Color | Black |
| Material | Alloy Steel, Aluminum, Glass |
| Finish Type | Painted |
| Base Material | Aluminum |
| Bulb Base | GY6.35 |
| Light Source Type | Halogen |
| Wattage | 35 watts |
| Voltage | 35 Volts |
| Switch Type | Touch |
| Special Feature | Adjustable, Balanced Electrical Conductor Arms |
| Product Dimensions | 39"D x 25"W x 39"H (Adjustable) |
| Item Weight | 4 Pounds |
| Indoor/Outdoor Usage | Indoor |
| Certification | ETL, UL |
Warranty and Support
Warranty information for your Artemide Tizio Table Lamp is typically provided with your purchase documentation or can be found on the official Artemide website. Please retain your proof of purchase for warranty claims.
For technical support, replacement parts, or further assistance, please contact Artemide customer service through their official website or the retailer from whom you purchased the lamp.
