1. Introduction
This manual provides essential information for the proper installation, function, and maintenance of your John Deere Original Equipment Oil Filter, model AM107423. Designed for optimal compatibility and performance with John Deere engines, this filter ensures enhanced engine protection by preventing dry starts and safeguarding against wear.
Key features include:
- Superior Design Adaptation: Specifically designed and tested to meet the unique requirements of John Deere engines.
- Advanced Filtration Technology: Utilizes a filter media combining natural cellulose and micro-fine synthetic fibers for thorough and even oil filtration.
- Robust Construction: Equipped with metal end discs for strength and durability under engine operation pressures.
- Reliable Oil Flow Management: Incorporates a precisely calibrated pressure relief bypass valve to prevent contaminants and oil starvation.
2. Safety Information
Always prioritize safety when working with machinery and engine components. Failure to follow safety instructions can result in injury or damage to equipment.
- Ensure the engine is turned off and cooled down before attempting any maintenance.
- Wear appropriate personal protective equipment (PPE), such as gloves and eye protection.
- Dispose of used oil and filters responsibly according to local regulations.
- Refer to your equipment's specific service manual for additional safety guidelines and procedures.
3. Installation Instructions
Follow these steps for proper installation of the John Deere AM107423 oil filter. Always consult your equipment's service manual for model-specific instructions.
- Prepare the Engine: Ensure the engine is off and cool. Place a drain pan beneath the oil filter to catch old oil.
- Remove Old Filter: Use an oil filter wrench to loosen and remove the old oil filter. Be prepared for oil to drain out.
- Clean Mounting Surface: Wipe the engine's oil filter mounting surface clean with a rag, ensuring no old gasket material remains.
- Lubricate New Filter Gasket: Apply a thin film of clean engine oil to the rubber gasket of the new John Deere AM107423 oil filter. This ensures a proper seal.
- Install New Filter: Screw the new filter onto the engine by hand until the gasket makes contact with the mounting surface.
- Tighten Filter: Once the gasket contacts the engine, tighten the filter an additional 1/2 to 3/4 turn by hand. Do not overtighten with a wrench, as this can damage the filter or engine.
- Refill Engine Oil: Add the recommended amount and type of fresh engine oil to your equipment.
- Check for Leaks: Start the engine and let it run for a few minutes. Turn off the engine and check for any oil leaks around the new filter. If leaks are present, tighten slightly or re-evaluate installation.
Image 1: John Deere AM107423 Oil Filter. This image shows the filter's side profile with a measuring tape, indicating its approximate height and diameter for reference during installation.
Image 2: John Deere AM107423 Oil Filter. This image provides another view of the filter with a measuring tape, highlighting its dimensions and the "MADE IN U.S.A." marking.
4. Function and Performance
The John Deere AM107423 oil filter is engineered to maintain the cleanliness of your engine oil, which is crucial for engine longevity and performance. Its advanced filtration media captures contaminants such as dirt, metal particles, and sludge, preventing them from circulating through the engine's vital components.
The integrated anti-drainback valve ensures that oil remains in the filter when the engine is off, preventing dry starts and reducing wear during initial engine startup. The pressure relief bypass valve is a critical safety feature, allowing unfiltered oil to bypass the filter if it becomes clogged, thus preventing oil starvation to the engine.
5. Maintenance
Regular replacement of your oil filter is vital for maintaining engine health. Refer to your John Deere equipment's owner's manual for the recommended oil and filter change intervals. Typically, oil filters should be replaced at every oil change, or at least once per operating season, whichever comes first.
Using genuine John Deere oil filters ensures that your equipment continues to operate with the filtration efficiency and protection it was designed for.
6. Troubleshooting
If you encounter issues after installing a new oil filter, consider the following common troubleshooting steps:
- Oil Leaks:
- Ensure the old gasket was completely removed from the engine block.
- Verify the new filter gasket was properly lubricated.
- Check if the filter is tightened correctly (hand-tight plus 1/2 to 3/4 turn). Overtightening or undertightening can cause leaks.
- Inspect the filter for any visible damage or defects.
- Low Oil Pressure Warning:
- Confirm the engine oil level is correct.
- Ensure the correct oil filter model (AM107423) was installed.
- If the issue persists, consult a qualified service technician.
7. Specifications
| Attribute | Detail |
|---|---|
| Brand | John Deere |
| Model Number | AM107423 |
| Material | Plastic (referring to internal components/gasket, filter housing is typically metal) |
| Product Grade | Replacement Part |
| Vehicle Service Type | Lawn Mower, Tractor, UTV |
| Item Dimensions (L x W x H) | Approximately 12.25 x 9.3 x 4.2 inches (packaging dimensions) |
| Thread Size | 0.75 inch |
| Item Weight | 6.4 ounces |
| UPC | 759936035753 |
Note: "Plastic" material specification likely refers to internal components or packaging, as typical oil filter housings are metal. Dimensions provided are often for packaging.
8. Warranty and Support
This John Deere Original Equipment Oil Filter AM107423 is manufactured to high-quality standards. For specific warranty information regarding this product, please refer to the warranty documentation provided with your John Deere equipment or contact John Deere customer support directly.
For technical assistance, parts inquiries, or further support, please visit the official John Deere website or contact your authorized John Deere dealer.
John Deere Official Website: www.deere.com
