Introduction
This manual provides instructions for the Satco S8130 21-Watt Mini Bi Pin T5 High Performance Fluorescent Lamp. This T5 fluorescent lamp operates at 21 watts, emits a 4100K Cool White light, and features an 85 CRI for accurate color rendering. It is designed with a Miniature Bi Pin base and offers an average rated life of 20,000 hours.
Important Safety Information
- Always turn off power at the circuit breaker before installation or replacement.
- Do not handle the lamp with bare hands; use gloves or a clean cloth to avoid oil transfer, which can reduce lamp life.
- Ensure the fixture is compatible with T5 fluorescent lamps and the correct wattage (21W).
- Dispose of fluorescent lamps according to local regulations, as they contain small amounts of mercury.
- Do not use in enclosed fixtures unless specifically rated for such use by the fixture manufacturer.
- Keep out of reach of children.
Setup and Installation
- Step 1: Power Off. Before beginning, ensure the power supply to the fixture is completely turned off at the circuit breaker or fuse box. Verify the power is off using a voltage tester.
- Step 2: Remove Old Lamp (if applicable). If replacing an existing lamp, carefully twist the old lamp 90 degrees and gently pull it out of the bi-pin sockets. Dispose of the old lamp properly according to local guidelines.
- Step 3: Insert New Lamp. Align the two pins on each end of the Satco S8130 lamp with the slots in the fixture's bi-pin sockets. Gently push the lamp into the sockets until the pins are fully seated. Then, rotate the lamp 90 degrees until it locks into place. Avoid excessive force during insertion.
- Step 4: Secure Connections. Ensure the lamp is securely seated in both sockets. A loose connection can cause flickering or prevent the lamp from lighting.
- Step 5: Restore Power. Once the lamp is securely installed, restore power at the circuit breaker.
- Step 6: Test. Turn on the light switch to confirm the lamp is functioning correctly.
Operating Instructions
The Satco S8130 fluorescent lamp operates by simply turning on the power switch connected to its fixture. Allow a few moments for the lamp to reach full brightness, especially in cooler environments.
- This lamp is designed for general illumination purposes.
- Frequent switching (turning on and off repeatedly) can reduce the overall lifespan of fluorescent lamps.
Maintenance
- Cleaning: To clean the lamp, ensure the power is off and the lamp is cool to the touch. Gently wipe the glass tube with a soft, dry, lint-free cloth. Do not use liquid cleaners directly on the lamp.
- Replacement: Replace the lamp when it reaches the end of its rated life (approximately 20,000 hours) or if it begins to flicker excessively, dims significantly, or fails to light. Follow the 'Setup and Installation' steps for proper replacement.
- Disposal: Fluorescent lamps contain small amounts of mercury. It is crucial to dispose of used lamps according to local, state, and federal environmental regulations. Many retailers and recycling centers offer specific programs for fluorescent lamp recycling.
Troubleshooting
| Problem | Solution |
|---|---|
| Lamp does not light. | Check power supply to the fixture. Ensure the lamp is correctly seated in its sockets. Inspect the lamp for any broken pins. If issues persist, replace with a new lamp. |
| Lamp flickers. | Ensure the lamp is securely seated in its sockets. Check for any loose wiring within the fixture. If flickering continues, the lamp may be nearing its end of life and should be replaced. |
| Lamp is dim. | A dim lamp often indicates that it is nearing the end of its operational life. Replace with a new lamp for optimal brightness. |
Specifications
| Model | S8130 |
| Wattage | 21 Watts |
| Light Type | Fluorescent |
| Color Temperature | 4100K (Cool White) |
| Color Rendering Index (CRI) | 85 |
| Base Type | Miniature Bi Pin (G5) |
| Average Rated Hours | 20,000 hours |
| Material | Glass |
| Length | 34.00 inches |
| UPC | 045923081309 |
Warranty and Support
This Satco S8130 lamp comes with a manufacturer's limited warranty, typically covering average rated hours. For specific warranty details or technical support, please contact Satco customer service or visit the official Satco website.
For further assistance, you may visit the Satco Store on Amazon.
