Introduction
The Pro-Ject Tuner Box S is a compact, high-quality FM tuner designed to integrate seamlessly into your audio system. This manual provides essential information for the proper installation, operation, and care of your device. Please read these instructions carefully before using the tuner to ensure safe and optimal performance.
Safety Instructions
- Power Supply: Only use the power supply provided with the unit. Ensure the voltage matches your local mains supply.
- Water and Moisture: Do not expose the device to rain, moisture, or excessive humidity. Avoid placing objects filled with liquids, such as vases, on or near the unit.
- Ventilation: Ensure adequate ventilation. Do not block ventilation openings.
- Heat Sources: Keep the unit away from direct sunlight, radiators, heat registers, stoves, or other heat-producing appliances.
- Servicing: Do not attempt to service the unit yourself. Refer all servicing to qualified service personnel.
- Cleaning: Disconnect the unit from the power supply before cleaning. Use a soft, dry cloth only.
Package Contents
Verify that your package contains the following items:
- Pro-Ject Tuner Box S Unit
- Power Supply
- IR Remote Control
- User Manual (this document)
Setup
Follow these steps to set up your Pro-Ject Tuner Box S:
1. Connecting the Antenna
Connect your FM antenna to the FM Ant. 75 Ohm input on the rear panel of the Tuner Box S. For optimal reception, use a high-quality outdoor FM antenna. If you are in a region that uses a different antenna connector type (e.g., PAL), an appropriate adapter may be required.
2. Connecting to an Amplifier/Receiver
Use a pair of RCA interconnect cables to connect the Left and Right audio outputs of the Tuner Box S to an available analog input on your amplifier or receiver (e.g., 'Tuner', 'Aux', 'CD').
3. Power Connection
Connect the supplied power supply to the Power 9V input on the rear of the unit. Then, plug the power supply into a suitable mains outlet. The unit will power on automatically or enter standby mode.
4. Trigger Connections (Optional)
The Tuner Box S features Trigger In and Trigger Out connections. These allow the unit to be switched on/off in conjunction with other compatible Pro-Ject components. If you are using this feature, connect a 2.5mm mono jack cable from the Trigger Out of a master component to the Trigger In of the Tuner Box S, or from the Trigger Out of the Tuner Box S to the Trigger In of a slave component.
Image: Rear panel of the Pro-Ject Tuner Box S. From left to right, it shows the FM Ant. 75 Ohm input, Left and Right RCA audio outputs, 9V Power input, and Trigger In/Out jacks. This panel illustrates all physical connections for the device.
Operating Instructions
1. Power On/Off
Press the power button on the front panel or the remote control to switch the unit between standby and operational mode.
2. Tuning
The Tuner Box S supports both manual and automatic tuning. Use the 'Up' and 'Down' arrow buttons on the front panel or remote to navigate frequencies. For automatic tuning, press and hold the 'Up' or 'Down' button to scan for the next available station. The high-contrast dot-matrix LCD display will show the frequency, preset number, and signal strength.
3. Saving Presets
The unit can store up to 99 station presets. To save a station:
- Tune to the desired FM station.
- Press the 'Memory' button on the remote or front panel.
- Use the 'Up' and 'Down' buttons to select a preset number.
- Press 'Memory' again to confirm and save the station to the selected preset.
4. Recalling Presets
Use the 'Preset Up' and 'Preset Down' buttons on the remote control to cycle through your saved stations.
Image: Front view of the Pro-Ject Tuner Box S. This image displays the compact size and silver finish of the unit, highlighting its minimalist design.
Maintenance
The Pro-Ject Tuner Box S requires minimal maintenance. To ensure its longevity and performance:
- Cleaning: Disconnect the unit from the power supply before cleaning. Use a soft, dry, lint-free cloth to wipe the casing. Do not use liquid cleaners, solvents, or abrasive materials.
- Ventilation: Ensure that the ventilation slots are not obstructed by dust or debris.
- Connections: Periodically check all cable connections to ensure they are secure.
Troubleshooting
If you encounter issues with your Tuner Box S, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No power | Power cable not connected; faulty power supply; mains outlet issue. | Check power cable connection; test power supply; try a different mains outlet. |
| No sound | RCA cables not connected; amplifier input not selected; low volume. | Ensure RCA cables are secure; select correct input on amplifier; increase volume. |
| Poor reception/static | Antenna not connected or poorly positioned; weak signal. | Check antenna connection; reposition antenna; consider a higher-gain outdoor antenna. |
| Remote control not working | Batteries depleted; line of sight blocked. | Replace batteries; ensure clear path between remote and unit. |
Specifications
- Product Dimensions: 4.06 x 4.06 x 1.42 inches
- Item Weight: 1.48 pounds
- Item Model Number: Tuner Box S
- Manufacturer: Vertical Cubed dba SUMIKO
- Date First Available: September 19, 2012
- Features: 99 station presets, Manual or automatic tuning with adaptive noise reduction, High-contrast dot-matrix LCD display, Full-function IR remote, Metal casework for interference protection.
Warranty and Support
Pro-Ject products are manufactured to the highest quality standards. This product is covered by a manufacturer's warranty, the terms of which may vary by region. Please retain your proof of purchase for any warranty claims.
For technical support, service, or further information, please contact your authorized Pro-Ject dealer or visit the official Pro-Ject Audio Systems website. Do not attempt to repair the unit yourself, as this may void your warranty.
