1. Introduction
The Satco S8369 is a 13-watt, pin-based Compact Fluorescent (CFL) tube featuring a 4100K color temperature and an 82 CRI (Color Rendering Index). It is designed with a 2GX7 (4-Pin) base, making it suitable for fixtures that utilize electronic and dimming ballasts. This manual provides essential information for the proper installation, operation, and maintenance of your Satco S8369 fluorescent tube.
Key features include:
- 13 Watts power consumption
- 800 Lumens brightness
- 4100 Kelvin (Bright White) color temperature
- 2GX7 (4-Pin) base type
- Designed for electronic and dimming ballasts
2. Safety Information
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Always observe the following safety precautions:
- Disconnect Power: Always turn off power to the fixture at the circuit breaker before installing, removing, or servicing the bulb.
- Handle with Care: Fluorescent tubes contain a small amount of mercury. Handle with care to avoid breakage. If a bulb breaks, follow local guidelines for cleanup and disposal.
- Correct Base Type: Ensure the bulb's base (2GX7, 4-Pin) matches your fixture's socket type. Incorrect base types can cause damage or electrical hazards.
- Compatible Ballast: This bulb requires an electronic or dimming ballast. Using it with an incompatible ballast (e.g., magnetic ballast) may cause flickering, reduced lifespan, or failure.
- Do Not Overwatt: Do not exceed the maximum wattage rating of your light fixture.
- Indoor Use: This bulb is generally intended for indoor, dry location use unless otherwise specified by the fixture.
3. Installation
Follow these steps to properly install your Satco S8369 Compact Fluorescent Tube:
- Turn Off Power: Before beginning, ensure the power supply to the light fixture is completely turned off at the circuit breaker or fuse box.
- Allow Cooling: If replacing an existing bulb, allow the old bulb to cool down completely before handling.
- Remove Old Bulb (if applicable): Gently twist or pull the old bulb straight out from the socket, depending on the fixture type. Avoid forcing it.
- Inspect Fixture: Check the fixture's socket for any damage or debris. Ensure it is clean and dry.
- Insert New Bulb: Align the four pins of the Satco S8369 bulb with the corresponding slots in the 2GX7 socket. Gently push the bulb straight into the socket until it is firmly seated. Do not twist or force the bulb, as this can bend the pins or damage the socket.
- Restore Power: Once the bulb is securely installed, restore power to the fixture at the circuit breaker.
- Test: Turn on the light switch to confirm the bulb is working correctly.
4. Operation
The Satco S8369 fluorescent tube is designed for straightforward operation once installed in a compatible fixture with an electronic or dimming ballast.
- Power On/Off: Use the standard wall switch or fixture control to turn the light on and off.
- Dimming Functionality: If your fixture is equipped with a compatible dimming ballast and dimmer switch, this bulb can be dimmed. Follow the instructions for your specific dimmer switch for proper operation.
- Color Temperature: The 4100K color temperature provides a bright white light, often described as cool white, suitable for task lighting, offices, and general illumination where a crisp, clear light is desired.
5. Maintenance
The Satco S8369 Compact Fluorescent Tube requires minimal maintenance. Regular cleaning can help maintain optimal light output.
- Cleaning: Ensure the power is off and the bulb is cool before cleaning. Gently wipe the glass tube with a soft, dry, lint-free cloth. Do not use liquid cleaners or abrasive materials, as these can damage the bulb or leave residues.
- Replacement: Replace the bulb when it reaches the end of its rated lifespan (approximately 15,000 hours) or if it begins to flicker excessively or fails to illuminate.
- Disposal: Due to the small amount of mercury contained in CFLs, proper disposal is important. Do not dispose of in regular household trash. Check with your local waste management authority for recycling or hazardous waste disposal options in your area. Many retailers also offer recycling programs for fluorescent bulbs.
6. Troubleshooting
If you encounter issues with your Satco S8369 fluorescent tube, consider the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Bulb does not light up. | No power to fixture; Bulb not seated correctly; Incompatible ballast; Defective bulb. | Check circuit breaker. Ensure bulb is fully inserted. Verify fixture has an electronic/dimming ballast. Replace bulb if necessary. |
| Bulb flickers. | Incompatible ballast; Loose connection; Bulb nearing end of life; Cold temperature. | Ensure ballast is compatible. Re-seat bulb. Replace bulb. Allow bulb to warm up in cold environments. |
| Bulb does not dim properly. | Incompatible dimmer switch or ballast; Bulb not designed for dimming. | Ensure both ballast and dimmer are compatible with dimmable CFLs. This S8369 model is designed for dimming ballasts. |
| Bulb does not fit the fixture. | Incorrect base type (e.g., 2-pin vs 4-pin, different GX base); Incorrect bulb length/width. | Verify the required base type and dimensions for your fixture. The S8369 has a 2GX7 (4-Pin) base and specific dimensions (see Section 3). |
If problems persist after attempting these solutions, contact Satco customer support or a qualified electrician.
7. Specifications
| Attribute | Value |
|---|---|
| Brand | Satco |
| Model Name | S8369 |
| Light Type | CFL (Compact Fluorescent) |
| Wattage | 13 watts |
| Brightness | 800 Lumens |
| Color Temperature | 4100 Kelvin (Bright White) |
| Color Rendering Index (CRI) | 82 |
| Bulb Shape Size | T4 |
| Bulb Base | 2GX7 (4-Pin) |
| Voltage | 120 Volts |
| Product Dimensions | 1.38"W x 6.19"H |
| Average Life | 15,000 Hours |
| Material | Glass |
| Special Feature | Frosted |
| Country of Origin | China |
| UPC | 045923083693 |
8. Warranty
The Satco S8369 Compact Fluorescent Tube comes with a 2-year limited warranty. This warranty covers defects in materials and workmanship under normal use and service. Please retain your proof of purchase for warranty claims. For specific terms and conditions, please refer to the official Satco warranty policy or contact customer support.
9. Support
For further assistance, technical inquiries, or warranty claims, please contact Satco customer support.
You can also visit the official Satco Store for more product information and resources:
