Satco S8320
Satco S8320 13-Watt GX23-2 Base T4 Quad 2-Pin Compact Fluorescent Lamp Instruction Manual
Model: S8320
Introduction
This manual provides essential instructions for the safe and efficient use of your Satco S8320 Compact Fluorescent Lamp (CFL). Please read this document thoroughly before proceeding with installation or operation to ensure proper function and longevity of the product.
Important Safety Instructions
Observe the following safety precautions to prevent injury or damage:
- Power Disconnection: Always disconnect the power supply to the fixture at the circuit breaker before installing, removing, or servicing the lamp.
- Ballast Compatibility: This lamp is designed exclusively for use with magnetic ballasts. Do not use with electronic ballasts or fixtures not specifically rated for GX23-2 base CFLs with magnetic ballasts.
- Dimmer Compatibility: This lamp is generally not suitable for use with dimmers unless the fixture and ballast are explicitly rated for dimmable CFLs. Using it with an incompatible dimmer may cause damage or reduce lamp life.
- Fixture Type: Do not use this lamp in totally enclosed fixtures unless the fixture is specifically designed for CFLs and allows for adequate ventilation.
- Handling: Avoid touching the glass tube with bare hands during installation. Oils from skin can create hot spots and reduce lamp life. Use a clean cloth or gloves.
- Disposal: Compact fluorescent lamps contain a small amount of mercury. Dispose of lamps according to local environmental regulations. Do not dispose of in regular household trash.
Product Overview
The Satco S8320 is a 13-watt T4 quad 2-pin compact fluorescent lamp. It is engineered to provide efficient illumination with a cool white light output of 4100 Kelvin and 780 lumens. This lamp is specifically designed for fixtures utilizing a GX23-2 base and magnetic ballasts.
Image: A close-up view of the Satco S8320 compact fluorescent lamp, showcasing its T4 quad tube design and GX23-2 2-pin base.
Setup and Installation
Follow these steps for safe and correct installation:
- Verify Power Off: Before touching the fixture or lamp, ensure the electrical power to the lighting fixture is completely turned off at the circuit breaker or fuse box.
- Check Fixture Compatibility: Confirm that your existing lighting fixture is designed to accept a GX23-2 base compact fluorescent lamp and operates with a magnetic ballast.
- Remove Old Lamp (if applicable): If replacing an existing lamp, gently pull the old lamp straight out from the socket. Avoid twisting.
- Insert New Lamp: Align the two pins of the Satco S8320 lamp with the corresponding slots in the GX23-2 socket. Gently push the lamp firmly into the socket until it is fully seated. Do not force the lamp, as this may damage the pins or the socket.
- Secure Connection: Ensure the lamp is securely and completely seated in the socket to establish proper electrical contact and prevent flickering.
- Restore Power: Once the lamp is securely installed, restore power to the fixture at the circuit breaker.
Operating Instructions
The Satco S8320 lamp is designed for straightforward operation:
- Initial Illumination: Upon first activation or after a power cycle, the lamp may exhibit a brief flicker before reaching full brightness. This is a normal characteristic of compact fluorescent technology.
- Light Output: The lamp provides a 4100K Cool White light, which is a bright, neutral white ideal for task lighting, offices, kitchens, or utility areas where clear visibility is desired.
- Operating Environment: This lamp is intended for indoor use. Optimal performance and lifespan are achieved in stable indoor environments. Avoid exposure to extreme temperatures or high humidity.
Maintenance
Minimal maintenance is required for the Satco S8320 lamp:
- Cleaning: To clean the lamp, ensure the power is off and the lamp has cooled completely. Gently wipe the glass tube with a soft, dry, lint-free cloth. Do not use liquid cleaners or abrasive materials.
- Replacement: Replace the lamp when it reaches the end of its operational life (approximately 12,000 hours) or if it consistently exhibits flickering, dimming, or fails to illuminate. Always replace with a lamp of the same type and wattage (Satco S8320 or an equivalent GX23-2 13-watt CFL).
- Disposal: Due to the mercury content, proper disposal is crucial. Do not discard used lamps in household waste. Contact your local waste management facility or recycling center for information on CFL recycling programs in your area.
Troubleshooting
Refer to the table below for common issues and their solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not light. | No power to fixture; Lamp not seated correctly; Defective lamp; Defective magnetic ballast. | Check power supply at circuit breaker; Re-seat lamp firmly into socket; Replace lamp with a new one; Consult a qualified electrician to inspect or replace the ballast. |
| Lamp flickers excessively. | Loose connection; Incompatible ballast (e.g., electronic instead of magnetic); End of lamp life. | Re-seat lamp to ensure secure contact; Verify fixture uses a magnetic ballast; Replace lamp if it is old or frequently used. |
| Lamp is dim or provides insufficient light. | End of lamp life; Incorrect wattage lamp installed. | Replace lamp with a new Satco S8320; Ensure the correct 13-watt lamp is used for the fixture. |
Technical Specifications
- Model: S8320
- Brand: Satco
- Wattage: 13 Watts
- Incandescent Equivalent: 55 Watts
- Base Type: GX23-2
- Bulb Shape: T4 Quad 2-Pin
- Light Type: Compact Fluorescent Lamp (CFL)
- Color Temperature: 4100 Kelvin (Cool White)
- Brightness: 780 Lumens
- Color Rendering Index (CRI): 82
- Average Rated Hours: 12,000 hours
- Voltage: 120 Volts
- Product Dimensions: Approximately 1.5"W x 1"H
- Material: Copper
- Indoor/Outdoor Usage: Indoor
- Special Feature: Designed for Magnetic Ballasts
- Compliance: UL Listed, RoHS Compliant, ENERGY STAR® certified
- UPC: 045923083204
Warranty and Customer Support
For information regarding product warranty, technical assistance, or any other inquiries, please contact Satco customer service directly. Refer to the original product packaging or the official Satco website for the most current contact details.
You can also find more products and information by visiting the Satco Store on Amazon.
Related documentsS8320
RELATED DOCUMENTSATCO S8320View document →RELATED DOCUMENTS8320 Specification SheetView document →RELATED DOCUMENTSATCO S7243 Compact Fluorescent Lamp, 23 W, ...View document →RELATED DOCUMENTSATCO S7227 Mini Spiral Compact Fluorescent Lamp, 23 ...View document →RELATED DOCUMENTSATCO S8369 CF13DS/E/841 Compact Fluorescent Lamp DatasheetDiscover the technical specifications and compliance details for the SATCO S8369 CF13DS/E/841, a 13-watt, 4100K Cool White compact fluorescent lamp with a 2GX7 (4-Pin) base, offering 800 lumens and a 15,000-hour rated life. Includes information on electrical, physical, and compliance attributes.View document →RELATED DOCUMENTSATCO S8369 CF13DS/E/841 Compact Fluorescent Lamp DatasheetDetailed technical specifications and compliance information for the SATCO S8369 CF13DS/E/841 13W T4 2GX7 (4-Pin) Compact Fluorescent Lamp, featuring 800 lumens, 4100K Cool White light, and a 15,000-hour rated life.View document →RELATED DOCUMENTSatco Nuvo Compact Fluorescent Lamps Product SpecificationsDetailed specifications for Satco Nuvo Twin Tube 4-Pin and Quad Tube 2-Pin compact fluorescent lamps, including wattage, lamp codes, color temperature, lumens, and dimensions for electronic, dimming, and magnetic ballasts.View document →RELATED DOCUMENTSATCO S8369 CFL Lamp Product Data SheetDiscover the SATCO S8369 13-watt pin-based compact fluorescent lamp (CFL) with a 2GX7 base, 4100K color temperature, and 82 CRI. This energy-efficient, low-mercury lamp is RoHS compliant and offers a 2-year limited warranty.View document →
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.