SunSun CBF-350C

Download PDF
Contents

SunSun CBF-350C Bio Pond Filter User Manual

Introduction

This manual provides essential information for the safe and efficient operation of your SunSun CBF-350C Bio Pond Filter. Please read these instructions carefully before installation and use to ensure optimal performance and longevity of the product. The SunSun CBF-350C is a 3-chamber flow-through filter designed for biological and mechanical purification of pond water, suitable for ponds up to 90,000 liters without fish and 40,000 liters with fish.

Safety Instructions

  • Always disconnect the power supply before performing any maintenance or cleaning.
  • Ensure all electrical connections are waterproof and installed according to local regulations.
  • This device is intended for outdoor use with pond water only.
  • Do not operate the filter if any part is damaged. Contact customer support for replacement parts.
  • Keep out of reach of children.

Product Components

Familiarize yourself with the parts of your SunSun CBF-350C Bio Pond Filter:

Exploded view of the SunSun CBF-350C pond filter with numbered parts and corresponding names.

Image Description: An exploded diagram of the SunSun CBF-350C pond filter, showing its various components disassembled. Each part is numbered and corresponds to a list for easy identification.

CBF-350C Parts List
No.PartNo.Part
1Cap8Sponges (coarse)
2Dirt Indicator9Pressure Filter Sponge
3Thermometer10Outlet
4Support Frame11Outlet Seal
5Carrying Frame12Outlet O-ring
6Filter Sponge Holder13Outlet Nut
7Sponges (fine)14Tray
15Seal
16Connecting Pipe
17Sealing Cover
18Ox-Add
19Inlet Seal
20Inlet

Setup and Installation

Proper installation is crucial for the filter's performance. Follow these steps:

  1. Placement: Position the filter on a stable, level surface near your pond. Ensure it is easily accessible for maintenance.
  2. Hose Connections: Connect the pond pump to the filter's inlet (marked 'In' or with an arrow pointing inwards) and the filter's outlet (marked 'Uit' or with an arrow pointing outwards) back to the pond. Use appropriate hose sizes and clamps to prevent leaks.
  3. UVC Connection (Optional): If using a compatible UVC clarifier (e.g., SunSun CUV236, CUV336, CUV636), connect it according to its specific instructions. The CBF-350C is designed to integrate with UVC units for enhanced algae control.
  4. Filter Media: Ensure all filter media (coarse sponges, fine sponges, Japan mats, bio balls) are correctly placed within their respective chambers as shown in the diagrams.
  5. Power Connection: Once all connections are secure and the filter is filled with water, connect the pump and any UVC unit to a grounded power outlet.
SunSun CBF-350C Bio Pond Filter installed next to a pond.

Image Description: The SunSun CBF-350C Bio Pond Filter system, consisting of three black rectangular units, is shown installed on a grassy bank adjacent to a pond with water lilies and fish. Water is being returned to the pond from the filter's outlet.

Overhead view of the SunSun CBF-350C Bio Pond Filter system with three chambers, positioned on grass next to a pond.

Image Description: An aerial perspective of the SunSun CBF-350C Bio Pond Filter, showcasing its three-chamber design. The filter is situated on a lush green lawn next to a pond, highlighting its outdoor placement.

Detailed dimensions of the SunSun CBF-350C Bio Pond Filter, showing overall length, width, height, and various connection sizes.

Image Description: A technical diagram displaying the precise measurements of the SunSun CBF-350C Bio Pond Filter. It includes overall dimensions (length, width, height) and specific diameters for various hose connections (20mm, 25mm, 32mm, 38mm, 50mm).

Operating Instructions

Once installed, the filter operates continuously to maintain water quality. Observe the following:

  • Initial Startup: After connecting the pump and UVC (if applicable), switch on the power. Water will begin to flow through the filter. It may take a few days for the biological filtration to fully establish.
  • Flow Rate: The filter is designed for a maximum flow rate of 12,000 liters per hour (l/h). Ensure your pond pump's flow rate is compatible.
  • Temperature Range: The filter system is robust and designed to operate reliably in temperatures between 8°C and 40°C.
  • Filtration Process: Water enters the first chamber for coarse mechanical filtration, then moves to the second chamber for finer mechanical filtration, and finally to the third chamber for biological filtration using Japan mats and bio balls.
Diagram illustrating the water flow through the three chambers of the SunSun CBF-350C filter, showing inlet, outlet, and maximum flow rates for different pond types.

Image Description: A schematic representation of the water purification process within the SunSun CBF-350C filter. It visually depicts water entering the 'In' port, flowing sequentially through three filter chambers, and exiting via the 'Uit' port. Key performance metrics like maximum flow rate (12000 l/h) and suitable pond volumes (90000 l without fish, 45000 l with fish) are also displayed.

Maintenance

Regular maintenance ensures the filter's effectiveness and extends its lifespan.

Filter Media Cleaning

The filter is equipped with a dirt indicator (part 2) that signals when cleaning is required. When the orange float rises, it's time to clean the filter material.

Instructions on how to clean the filter material, showing the dirt indicator, removing sponges, squeezing them with water, and draining dirty water.

Image Description: A four-step visual guide demonstrating the cleaning process for the filter material. It shows the dirt indicator, the removal of filter sponges, the method of squeezing sponges in water, and the draining of dirty water from the filter.

  1. Observe Dirt Indicator: The orange float indicates when the filter material needs cleaning.
  2. Prepare for Cleaning: Disconnect power to the pump and UVC unit.
  3. Clean Sponges: Remove the filter sponges from their chambers. Do not clean all sponges at once to preserve beneficial bacteria. Squeeze and rinse them thoroughly in a bucket of pond water (not tap water, as chlorine can harm bacteria).
  4. Clean Bio Balls and Japan Mats: Gently rinse bio balls and Japan mats with pond water if they appear heavily soiled. Avoid aggressive cleaning to protect the biological film.
  5. Drain Dirty Water: Use the dirt drain at the bottom of the system to remove accumulated sludge.
  6. Reassemble and Restart: Place the cleaned media back into the filter, secure the lid, and reconnect power.
Close-up view of water flowing through filter sponges, demonstrating the mechanical filtration process of the SunSun CBF-350C filter.

Image Description: A close-up illustration of water passing through blue and yellow filter sponges, highlighting the mechanical filtration stage where impurities and debris are captured.

Diagram showing the internal filter media of the SunSun CBF-350C, including bio balls, filter sponges (coarse and fine), and Japanese filter mats, with descriptions of their functions.

Image Description: A cutaway diagram revealing the internal structure of the SunSun CBF-350C filter. It clearly shows the arrangement of bio balls (approximately 30, providing ideal surface for beneficial bacteria), coarse and fine filter sponges (8 coarse, 4 fine), and Japanese filter mats (optimal material for nitrifying bacteria).

Close-up of the thermometer and dirt indicator on the SunSun CBF-350C filter, showing the temperature range and how the orange float indicates when cleaning is needed.

Image Description: A detailed view of the thermometer and dirt indicator integrated into the SunSun CBF-350C filter. The thermometer displays a temperature range of 8°C to 40°C, while the orange float of the dirt indicator is visible, signaling the need for filter material cleaning.

Troubleshooting

If you encounter issues with your pond filter, consider the following common problems and solutions:

  • Reduced Water Flow: Check if the pump is clogged or if hoses are kinked. Clean the filter media as described in the maintenance section.
  • Cloudy Water: This often indicates that the filter media needs cleaning or that the biological filtration is not fully established. Ensure the UVC unit (if installed) is functioning correctly. Check for excessive organic load in the pond.
  • Leaks: Inspect all hose connections and seals for proper fit. Ensure the lid is securely closed.
  • Filter Not Starting: Verify that the power supply is connected and working. Check the pump for any blockages or malfunctions.

For persistent issues, contact SunSun customer support.

Specifications

FeatureSpecification
BrandSunSun
Model Number50114
Filter TypeBio Pond Filter (3-chamber flow-through)
Max. Pond Volume (without fish)90,000 Liters
Max. Pond Volume (with fish)40,000 Liters
Max. Flow Rate12,000 l/h
Liquid Volume (Filter)180 Liters
Item Weight17.62 Kilograms
Operating Temperature Range8°C to 40°C
Country of OriginChina

Warranty and Support

SunSun products are manufactured to high-quality standards. For warranty information, please refer to the documentation provided at the time of purchase or contact your retailer. If you require technical assistance or have questions regarding your SunSun CBF-350C Bio Pond Filter, please contact SunSun customer support or visit the official SunSun website for further resources.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.