1. Product Overview
The Eibach Pro-Kit Lowering Springs (Model E10-35-020-01-22) are designed to enhance the performance and appearance of your Ford Fiesta VI. This kit provides a lowering of approximately 30mm, resulting in improved road holding, reduced body roll, and increased driving safety. Eibach Pro-Kit springs are engineered for optimal balance between performance and ride comfort, making them suitable for daily driving.
This product is compatible with Ford Fiesta VI models including 1.0, 1.0 EcoBoost, 1.25, 1.4, 1.5 Flex, 1.5 Duratec, 1.6, and 1.6 Ti, as well as Facelift models.
Figure 1: Eibach Pro-Kit Lowering Springs, showing the four springs and product packaging.
2. Components Included
The Eibach Pro-Kit E10-35-020-01-22 package contains the following items:
- 4x Eibach Lowering Springs
Figure 2: Illustration of the Eibach Pro-Kit Performance Suspension Springs.
3. Installation (Setup)
Professional installation by a qualified technician is strongly recommended for this product. Improper installation can lead to vehicle damage, compromised safety, and voiding of the product warranty.
3.1. General Installation Steps (Consult a professional service manual for your specific vehicle model):
- Vehicle Preparation: Safely lift and support the vehicle on jack stands. Remove the wheels.
- Disassembly: Carefully disconnect and remove the original suspension components (struts/shocks and springs). A spring compressor tool is essential for safe removal of the original springs.
- Spring Replacement: Using a suitable spring compressor, compress the new Eibach Pro-Kit springs and install them onto the struts/shocks. Ensure all components are correctly seated and torqued to manufacturer specifications.
- Reassembly: Reinstall the complete strut/shock assembly into the vehicle. Reconnect all suspension components, ensuring proper torque on all fasteners.
- Final Checks: Lower the vehicle. It is crucial to perform a wheel alignment immediately after installing lowering springs to ensure correct steering geometry and tire wear.
Always refer to your vehicle's specific service manual for detailed, step-by-step instructions and torque specifications.
4. Operating Characteristics
After installation, you will experience a noticeable change in your vehicle's driving dynamics:
- Lowered Stance: The vehicle's ride height will be reduced by approximately 30mm, giving it a more aggressive and sporty appearance.
- Improved Handling: The stiffer spring rates and lower center of gravity contribute to enhanced cornering stability, reduced body roll, and more precise steering response.
- Ride Comfort: While designed for performance, Eibach Pro-Kit springs aim to maintain a good balance of ride comfort for daily use. You may notice a slightly firmer ride compared to stock springs, especially over bumps and uneven surfaces, but it should not significantly compromise overall comfort.
- Increased Safety: The improved handling characteristics contribute to a safer driving experience, particularly during evasive maneuvers.
5. Maintenance
Eibach Pro-Kit lowering springs are designed for durability and typically require minimal direct maintenance. However, regular inspection of your vehicle's suspension system is crucial:
- Regular Inspection: Periodically inspect the springs for any signs of damage, corrosion, or cracks. Also check the condition of related suspension components such as shock absorbers, bushings, and mounts.
- Cleaning: Keep the springs and surrounding suspension components clean from dirt, salt, and debris, especially in harsh weather conditions.
- Alignment: Ensure wheel alignment is checked periodically, especially after any significant impact or if uneven tire wear is observed.
6. Troubleshooting
If you encounter any issues after installing your Eibach Pro-Kit springs, consider the following:
- Unusual Noises (Clunking, Squeaking): This could indicate improper installation, loose components, or worn bushings. Re-check all fasteners and inspect bushings.
- Uneven Ride Height: Verify that the correct springs are installed in the correct positions (front/rear) and that all components are properly seated. Ensure the vehicle is on a level surface when checking height.
- Poor Handling or Excessive Bounciness: This might suggest an issue with the shock absorbers, which may not be adequately matched to the stiffer lowering springs, or an incorrect wheel alignment.
For persistent issues, consult a professional automotive technician. Do not attempt to drive the vehicle if you suspect a safety-critical suspension problem.
7. Specifications
| Attribute | Value |
|---|---|
| Manufacturer | Eibach |
| Brand | Eibach |
| Model | 10 35 020 01 22 |
| Item Weight | 7.66 Kilograms |
| Product Dimensions | 64 x 18 x 38 cm |
| Item Model Number | E10-35-020-01-22 |
| Manufacturer Part Number | E10-35-020-01-22 |
| OEM Part Number | 0 |
| Position | Rear (Note: Product description indicates compatibility for full vehicle, but 'Position' spec says 'Rear'. Consult Eibach for full kit details.) |
| ASIN | B007G8AK72 |
| Lowering Amount | Approximately 30mm |
| Compatibility | Ford Fiesta VI (1.0, 1.0 EcoBoost, 1.25, 1.4, 1.5 Flex, 1.5 Duratec, 1.6, 1.6 Ti), including Facelift models |
Figure 3: Detailed view of a single Eibach Pro-Kit Performance Spring.
8. Warranty Information
Eibach Pro-Kit Lowering Springs come with TÜV certified quality and a 5-year product warranty. This warranty covers manufacturing defects and material flaws under normal use. Please retain your proof of purchase for warranty claims. For full warranty terms and conditions, refer to the official Eibach website or contact Eibach customer service.
9. Support and Contact
For further assistance, technical questions, or support regarding your Eibach Pro-Kit Lowering Springs, please:
- Visit the official Eibach website for FAQs and detailed product information.
- Contact your authorized Eibach dealer or the point of purchase.
- Refer to your vehicle's specific service manual for any vehicle-related procedures.
