Introduction
This manual provides essential information for the installation, operation, and maintenance of your Clean Comfort Whole Home Media Air Cleaner, Model AM11-1620-5. This advanced air cleaner is designed to significantly improve indoor air quality by removing common airborne pollutants.
The Clean Comfort AM11-1620-5 features a 16"x20" MERV 11 rated filter, offering superior filtration compared to standard furnace filter systems. It effectively captures pet hair, dust, pollen, tobacco smoke, and other particles that can cause allergic reactions and trigger asthma symptoms. Its versatile design allows for easy integration into your home's central heating and air conditioning system, also protecting against coil corrosion.
Safety Information
Please read all instructions carefully before installing or operating the unit. Failure to follow these instructions may result in property damage, personal injury, or death.
- Always disconnect power to the HVAC system before performing any installation or maintenance.
- Wear appropriate personal protective equipment (PPE) such as gloves and eye protection during installation and maintenance.
- Ensure the unit is installed by a qualified technician in accordance with local and national electrical and building codes.
- Do not operate the unit without the filter properly installed.
Product Overview
Setup and Installation
The Clean Comfort Whole Home Media Air Cleaner is designed for integration into your existing HVAC ductwork. Professional installation is recommended.
Pre-Installation Checklist:
- Verify the unit dimensions (16"D x 5"W x 20"H) against available space in your ductwork.
- Ensure all components are present and undamaged.
- Turn off power to the furnace/air handler at the circuit breaker.
Installation Steps (General):
- Locate a suitable position in the return air ductwork, typically before the furnace/air handler.
- Cut an opening in the ductwork according to the unit's specifications.
- Slide the air cleaner into the opening, ensuring a tight seal to prevent air bypass.
- Secure the unit to the ductwork using appropriate fasteners.
- Install the MERV 11 filter into the unit, ensuring correct airflow direction.
- Restore power to the HVAC system and test for proper operation.
Operating Instructions
The Clean Comfort Whole Home Media Air Cleaner operates passively with your HVAC system. Once installed, it filters the air as it circulates through your home's heating and cooling system.
- Ensure your HVAC system fan is set to "Auto" or "On" for continuous air filtration.
- The unit does not have external controls; its operation is tied to your furnace or air handler.
- For optimal air quality, run your HVAC fan periodically even when heating or cooling is not required.
Maintenance
Regular maintenance, primarily filter replacement, is crucial for the optimal performance and longevity of your air cleaner.
Filter Replacement:
- The MERV 11 filter should be inspected every 3-6 months and replaced as needed, depending on usage and household conditions (e.g., pets, smoking, construction).
- A dirty filter will reduce airflow and filtration efficiency.
Steps for Filter Replacement:
- Turn off power to your HVAC system at the circuit breaker.
- Locate the filter access door on the air cleaner unit.
- Open the access door and carefully slide out the old filter. Note the airflow direction arrow on the filter frame.
- Insert the new 16"x20" MERV 11 replacement filter, ensuring the airflow arrow points in the correct direction (towards the furnace/air handler).
- Close and secure the filter access door.
- Restore power to the HVAC system.
Troubleshooting
This section addresses common issues you might encounter with your air cleaner.
| Problem | Possible Cause | Solution |
|---|---|---|
| Reduced Airflow | Clogged filter | Replace the MERV 11 filter. |
| Poor Air Quality | Filter needs replacement; Air bypass around filter. | Replace filter; Ensure unit is properly sealed in ductwork. |
| Unusual Noises | Loose components; Obstruction. | Inspect unit for loose parts; Remove any obstructions. If noise persists, contact a qualified technician. |
Specifications
| Feature | Detail |
|---|---|
| Model | AM11-1620-5 |
| Filter Type | MERV 11 Media Filter |
| Filter Dimensions | 16" x 20" |
| Product Dimensions | 16"D x 5"W x 20"H |
| Weight | 17 Pounds |
| Manufacturer | Clean Comfort |
| ASIN | B007C608KW |
Warranty and Support
For warranty information or technical support, please contact Clean Comfort customer service. Keep your purchase receipt and product model number (AM11-1620-5) handy when contacting support.
While specific warranty details are not provided in this manual, Clean Comfort products are designed for durability and performance. Refer to the official Clean Comfort website or your product packaging for the most current warranty terms and conditions.
For replacement filters or additional product information, visit the Clean Comfort brand page on Amazon or consult your local HVAC professional.
