Introduction
Thank you for choosing the Sunlite TL-L200 Griplite Tail Light. This manual provides essential information for the proper installation, operation, and maintenance of your new tail light. Designed for enhanced visibility and safety, this light features bright LEDs and a durable, water-resistant silicone body. Please read this manual thoroughly before use and retain it for future reference.
Safety Information
- Always ensure the tail light is securely mounted before riding.
- Do not look directly into the LED light as it may cause temporary vision impairment.
- While the light is water-resistant, avoid prolonged submersion.
- Regularly check battery life to ensure consistent performance.
- This light is intended to increase visibility to others; it does not replace the need for safe riding practices.
Package Contents
Verify that all items are present in the package:
- 1 x Sunlite TL-L200 Griplite Tail Light
- 2 x CR2032 Lithium Batteries (pre-installed)
Setup
Battery Installation (If not pre-installed or for replacement)
- Gently open the silicone casing to access the battery compartment.
- Insert two CR2032 lithium batteries, ensuring correct polarity (+/-).
- Close the silicone casing securely to maintain water resistance.
Mounting the Tail Light
The Sunlite Griplite Tail Light features an integrated silicone mounting strap for versatile attachment.
- Identify a suitable mounting location on your bicycle, such as the seat post, seat stay, or rear rack. Ensure the light will be visible from the rear.
- Wrap the integrated silicone strap around the desired mounting point.
- Hook the end of the strap onto the designated tab on the light's body, pulling it taut to secure the light firmly in place.
- Adjust the light's angle to ensure optimal visibility.
Image: The Sunlite TL-L200 Griplite Tail Light securely mounted on a bicycle seat post, demonstrating its flexible silicone strap attachment.
Operating Instructions
The Sunlite TL-L200 Griplite Tail Light operates with a simple one-button control located on the top of the light.
Image: Front view of the Sunlite TL-L200 Griplite Tail Light, highlighting the prominent power button on its top surface.
- Power On/Off: Press the button once to turn the light on. Press and hold the button for approximately 2 seconds to turn the light off.
- Change Modes: With the light on, press the button repeatedly to cycle through the available lighting modes:
- Steady Mode: Provides a continuous beam of red light for constant visibility.
- Flashing Mode: Emits a pulsating red light, designed to attract attention and enhance safety.
Image: The Sunlite TL-L200 Griplite Tail Light illuminated in a dark environment, demonstrating its bright red light output and visibility.
Maintenance
Cleaning
To clean your tail light, wipe the silicone body and lens with a soft, damp cloth. Avoid using abrasive cleaners or solvents, as these may damage the material or lens.
Battery Replacement
When the light appears dim or stops functioning, it's time to replace the batteries. Refer to the "Battery Installation" section under "Setup" for detailed instructions. Always use two new CR2032 lithium batteries for optimal performance.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | Dead batteries or incorrect battery installation. | Replace batteries with new CR2032 cells, ensuring correct polarity. |
| Light is dim. | Low battery power. | Replace batteries. |
| Light flickers. | Loose battery connection or low battery power. | Check battery compartment for secure fit; replace batteries if necessary. |
| Light falls off during ride. | Improper mounting. | Ensure the silicone strap is pulled taut and securely hooked onto the tab. |
Specifications
- Model: Sunlite TL-L200 Griplite Tail Light (Part Number: 97525)
- Light Source: 2 x Bright Nichia LEDs
- Power Source: 2 x CR2032 Lithium Batteries (included)
- Run Time: Up to 100 hours (depending on mode and battery quality)
- Modes: 1 Steady, 1 Flashing
- Material: Water-resistant Silicone Body
- Mounting Type: Integrated Silicone Strap (Seat Mount)
- Item Weight: Approximately 0.94 Pounds
- Dimensions (LxWxH): Approximately 4.7 x 3.25 x 1.45 inches
- Water Resistance Level: Water Resistant
- UPC: 072774975259
Warranty and Support
Sunlite products are manufactured to high standards. For specific warranty information or technical support, please refer to the product packaging or visit the official Sunlite website. Keep your purchase receipt as proof of purchase.
For further assistance, please contact Sunlite customer service through their official channels.
