Philips 24675-1 40W Fluorescent Lamp Instruction Manual

Important Safety Information

Read all instructions carefully before installing or using the Philips 24675-1 fluorescent lamp. Failure to follow these instructions may result in electric shock, fire, or other hazards.

WARNING: Risk of electric shock. Disconnect power before installation or servicing.
Ensure the lamp is compatible with your fixture's ballast and voltage requirements (50 Volts).
Do not use with dimmers unless specifically rated for fluorescent lamps and compatible with the ballast.
Handle lamps carefully. Avoid dropping or subjecting them to impact.
Dispose of fluorescent lamps according to local regulations, as they contain mercury.
Do not operate in wet locations or where directly exposed to water.

Setup and Installation

This section provides instructions for safely installing your Philips 24675-1 fluorescent lamp.

Required Tools and Materials:

Philips 24675-1 Fluorescent Lamp
Compatible fluorescent fixture
Stepladder (if necessary)
Safety gloves and eye protection

Installation Steps:

Step 1: Disconnect Power. Locate the circuit breaker or fuse box that controls the power to the light fixture. Turn off the power completely. Verify power is off using a voltage tester if available.
Step 2: Remove Old Lamp (if applicable). If replacing an existing lamp, carefully twist the old fluorescent tube 90 degrees and gently pull it out of the lampholders. Dispose of the old lamp properly.
Step 3: Insert New Lamp. Align the pins on both ends of the Philips 24675-1 fluorescent lamp with the slots in the lampholders of your fixture. Gently push the lamp into the lampholders until the pins are fully seated.
Step 4: Rotate Lamp. Once seated, rotate the lamp 90 degrees until it locks securely into place. Ensure both ends are firmly connected and the lamp is stable.
Step 5: Restore Power. Once the lamp is securely installed, restore power to the fixture from the circuit breaker or fuse box.
Step 6: Test Operation. Turn on the light switch to confirm the lamp illuminates.

Image of Philips 24675-1 40W Fluorescent Lamp

Figure 1: Philips 24675-1 40W Fluorescent Lamp. This image shows the tubular shape and standard pins of the fluorescent lamp, ready for installation into a compatible fixture.

Operating Instructions

The Philips 24675-1 fluorescent lamp is designed for straightforward operation within a compatible fixture.

Power On/Off: Use the wall switch or fixture switch to turn the lamp on or off.
Warm-up Time: Fluorescent lamps may require a brief warm-up period (a few seconds) to reach full brightness, especially in colder environments.
Normal Operation: The lamp will provide consistent illumination once fully warmed up.

Note: Frequent switching on and off can reduce the lifespan of fluorescent lamps. For optimal longevity, avoid rapid cycling.

Maintenance

Proper maintenance ensures optimal performance and extends the life of your Philips 24675-1 fluorescent lamp.

Cleaning: Ensure power is off before cleaning. Gently wipe the lamp with a soft, dry, lint-free cloth. Do not use liquid cleaners or abrasive materials.
Inspection: Periodically inspect the lamp and fixture for any signs of damage, loose connections, or discoloration. If any issues are found, disconnect power and consult a qualified electrician.
Replacement: Replace the lamp when it reaches the end of its average rated life (2000 hours) or if it begins to flicker excessively, dims significantly, or fails to illuminate.
Disposal: Fluorescent lamps contain small amounts of mercury. Do not dispose of them in regular household trash. Consult your local waste management authority for proper recycling or disposal procedures.

Troubleshooting

If you experience issues with your Philips 24675-1 fluorescent lamp, refer to the following common problems and solutions:

Problem	Possible Cause	Solution
Lamp does not light up.	No power to fixture. Lamp not properly seated. Defective lamp. Defective ballast or fixture.	Check circuit breaker/fuse. Ensure lamp is fully inserted and rotated 90 degrees. Replace lamp with a new one. Consult a qualified electrician to inspect the fixture/ballast.
Lamp flickers or hums.	Lamp nearing end of life. Incorrect or failing ballast. Loose connection. Cold ambient temperature.	Replace lamp. Consult a qualified electrician to inspect/replace ballast. Ensure lamp is securely seated. Allow lamp to warm up.
Reduced brightness.	Lamp nearing end of life. Dust or dirt on lamp/fixture.	Replace lamp. Clean lamp and fixture (ensure power is off).

Product Specifications

Detailed technical specifications for the Philips 24675-1 40W Fluorescent Lamp.

Model Number: 24675-1
Brand: Philips
Light Type: Fluorescent
Wattage: 40 Watts
Voltage: 50 Volts
Shape: Tubular (T)
Brightness: 140 Lumens
Color Temperature: 2700 Kelvin
Color Rendering Index (CRI): 80
Average Life: 2000 hours
Product Dimensions: 1.75 x 1.75 x 24.5 inches
Item Weight: 6.4 ounces
Specific Uses: Lamp

Warranty and Support

For warranty information or technical support regarding your Philips 24675-1 fluorescent lamp, please refer to the official Philips website or contact their customer service directly.

Note: Warranty terms and conditions may vary by region and retailer. Keep your purchase receipt for warranty claims.

	Philips Fluorescent Lamp Safety and Handling Guide Essential safety instructions for Philips fluorescent lamps, covering electrical hazards, breakage precautions, and mercury disposal procedures.
	Philips Ultinon Pro7000 SI LED Festoon Bulb: Enhanced Interior Lighting Discover the Philips Ultinon Pro7000 SI LED festoon bulbs (LUM11860CU70X1/20) for your car. Offering superior brightness (6000 K), uniform light distribution, and a 5,000-hour lifespan, these bulbs enhance driving safety and interior style with easy plug-and-play installation.
	Philips CorePro G24q-3 LED 9.5W Installation Guide Installation guide for the Philips CorePro G24q-3 LED 9.5W (26W equivalent) 4-pin bulb, detailing compatibility, usage, and wiring instructions for electronic ballasts and AC mains.
	Philips Lamp Specification Guide SG-100: Energy Saving Lighting Solutions Discover the Philips Lamp Specification Guide SG-100 for comprehensive details on incandescent, fluorescent, and high-intensity discharge lamps. This guide provides essential data and energy-saving substitution recommendations, featuring the Econ-o-watt line to help reduce lighting costs.
	Philips Consumer Lamps Catalog 2015: Experience Exciting Light Explore the comprehensive 2015 portfolio of Philips consumer lamps, offering innovative lighting solutions designed to enhance living spaces. This catalog details a wide array of lamps, from energy-efficient LED and fluorescent options to classic halogen and GLS bulbs, catering to diverse lighting needs and preferences.
	Philips Hue Outdoor Lighting Fixture and Smart Bulb Installation Guide Comprehensive guide for installing Philips Hue outdoor lighting fixtures and setting up Philips Hue A19 smart LED bulbs, including safety instructions, setup steps, and Hue system overview. Covers installation, wiring, bulb setup, and smart features.

Philips 24675-1