Introduction
The Electro-Voice EVID 6.2T is a high-performance, two-way surface-mount loudspeaker designed for various installation applications. It features dual 6-inch woofers and a 1-inch tweeter, providing clear audio reproduction across a wide frequency range. This model includes 70V/100V transformer taps for flexible integration into commercial audio systems and is housed in a weather-resistant enclosure, making it suitable for both indoor and outdoor use. The speaker also incorporates overload protection for enhanced durability and reliability.
What's in the Box
- One pair of Electro-Voice EVID 6.2T Loudspeakers
Setup and Installation
Proper installation is crucial for optimal performance and safety. It is recommended that installation be performed by a qualified professional.
Mounting
The EVID 6.2T is designed for surface mounting. Ensure the mounting surface is structurally sound and capable of supporting the speaker's weight (approximately 34.3 pounds per speaker). Use appropriate hardware for secure attachment. The weather-resistant enclosure allows for outdoor installation, but ensure all connections are properly sealed and protected from direct water exposure.
This image displays the front of the Electro-Voice EVID 6.2T speaker. It features two 6-inch woofers positioned vertically, with a horn-loaded tweeter located between them. The speaker enclosure is black and designed for surface mounting.
Wiring
The EVID 6.2T can be connected in either an 8-ohm low impedance configuration or a 70V/100V constant voltage system. Select the appropriate wiring method based on your amplifier and system design.
- 8-Ohm Connection: Connect directly to a low-impedance amplifier output. Ensure the amplifier's impedance rating matches or exceeds the speaker's 8-ohm rating.
- 70V/100V Connection: Utilize the integrated transformer taps. Select the desired wattage tap (e.g., 30W, 60W, 120W) on the speaker to match the power requirements of your constant voltage system. Connect to the 70V or 100V output of your amplifier.
Always ensure the amplifier is turned off before making any connections to prevent damage to the equipment.
Operating Instructions
Once properly installed and wired, operating the EVID 6.2T speakers is straightforward.
- Power On: Turn on your audio amplifier.
- Source Selection: Select the desired audio source on your amplifier or mixer.
- Volume Adjustment: Gradually increase the volume on your amplifier to the desired listening level. Avoid setting the volume too high, which can cause distortion and potentially damage the speakers. The EVID 6.2T includes overload protection to help prevent damage from excessive power.
- Power Off: When finished, decrease the volume and turn off your amplifier.
Maintenance
Regular maintenance helps ensure the longevity and performance of your speakers.
- Cleaning: Wipe the speaker enclosure with a soft, dry cloth. For stubborn dirt, a slightly damp cloth can be used, but avoid harsh chemicals or abrasive cleaners. Ensure no liquid enters the speaker grilles or ports.
- Connection Inspection: Periodically check all wiring connections to ensure they are secure and free from corrosion. Loose connections can lead to poor sound quality or intermittent operation.
- Environmental Considerations: While weather-resistant, prolonged exposure to extreme conditions (e.g., direct sunlight, heavy rain, snow, extreme temperatures) can affect performance and lifespan. If possible, provide some protection in harsh environments.
Troubleshooting
If you encounter issues with your EVID 6.2T speakers, refer to the following common troubleshooting steps:
- No Sound:
- Verify the amplifier is powered on and functioning correctly.
- Check all audio cable connections from the source to the amplifier and from the amplifier to the speakers. Ensure they are secure.
- Confirm the correct input source is selected on your amplifier/mixer.
- Ensure the volume on the amplifier is turned up.
- Distorted Sound:
- Reduce the volume level on your amplifier. Overdriving the speakers can cause distortion.
- Check for loose wiring connections.
- Ensure the amplifier's output power and impedance match the speaker's requirements (8-ohm or correct 70V/100V tap).
- Intermittent Sound:
- Inspect all cable connections for looseness or damage.
- Check for any short circuits in the speaker wiring.
If these steps do not resolve the issue, contact Electro-Voice customer support for further assistance.
Specifications
| Feature | Specification |
|---|---|
| Model | EVID 6.2T |
| Speaker Type | 2-way Surface-Mount Loudspeaker |
| Woofer Size | Dual 6-inch |
| Tweeter Size | 1-inch |
| Power Handling | 300 watts |
| Impedance | 8-ohm (nominal) |
| Transformer Taps | 70V/100V |
| Enclosure | Weather-resistant |
| Protection | Overload Protection |
| Speaker Amplification Type | Passive |
| Material Type | Stainless Steel (likely for mounting hardware/grille) |
| Dimensions (L x W x H) | 21.65 x 18.5 x 15.35 inches |
| Item Weight | 34.3 pounds |
Warranty and Support
For detailed warranty information, technical support, or service inquiries regarding your Electro-Voice EVID 6.2T loudspeakers, please refer to the official Electro-Voice website or contact their customer service department directly. Keep your purchase receipt as proof of purchase for warranty claims.
