Rittal 8017637 316L Stainless Steel Wallmount Enclosure Instruction Manual

1. Product Overview

The Rittal 8017637 Wallmount Enclosure is designed for industrial applications requiring robust protection for electrical and electronic components. Constructed from durable 316L stainless steel, this enclosure features a one-piece body for enhanced integrity and ease of installation. It is engineered to withstand harsh environments, offering superior protection against dust, water, and corrosion.

Figure 1: Rittal 8017637 316L Stainless Steel Wallmount Enclosure. This image displays the front view of the enclosure, highlighting its brushed stainless steel finish and integrated latch mechanism.

Key features include a left-hand hinged door, a zinc-plated mounting panel for component installation, and two 1/4 turn latches with slotted head inserts for secure closure. The enclosure is sealed with a foamed-in-place polyurethane gasket and utilizes wall-mounting blind-nuts for a secure attachment.

2. Safety Information

Please read and understand all safety instructions before installing, operating, or performing maintenance on the Rittal 8017637 enclosure. Failure to follow these instructions may result in property damage, serious injury, or death.

• Qualified Personnel: Installation and maintenance should only be performed by qualified and authorized personnel familiar with electrical systems and enclosure installation practices.
• Disconnect Power: Always ensure that all power sources are disconnected and locked out before working inside the enclosure or performing any installation procedures.
• Proper Grounding: Ensure the enclosure is properly grounded according to local and national electrical codes.
• Weight: The enclosure is heavy (approximately 30 pounds). Use appropriate lifting techniques and equipment to prevent injury.
• Sharp Edges: Exercise caution when handling the enclosure and its components, as some edges may be sharp.

3. Package Contents

Verify that all components are present and undamaged upon receipt of the product. If any items are missing or damaged, contact your supplier immediately.

• Rittal 8017637 316L Stainless Steel Wallmount Enclosure
• Zinc-plated Mounting Panel

4. Technical Specifications

5. Installation Instructions

This section outlines the general steps for installing the Rittal 8017637 Wallmount Enclosure. Always refer to local and national electrical codes for specific requirements.

5.1 Site Selection

• Choose a flat, stable, and structurally sound wall capable of supporting the enclosure's weight plus the weight of its contents.
• Ensure adequate clearance around the enclosure for door opening, maintenance, and proper ventilation if required by internal components.
• Consider environmental factors such as temperature, humidity, and potential for mechanical impact.

5.2 Mounting the Enclosure

1. Carefully unpack the enclosure and inspect it for any shipping damage.
2. Using the enclosure's dimensions and mounting points, mark the drilling locations on the wall. The enclosure is equipped with wall-mounting blind-nuts for secure attachment.
3. Drill appropriate holes in the wall and install suitable anchors or fasteners (not supplied) that are rated for the combined weight of the enclosure and its intended contents.
4. Carefully lift the enclosure into position and secure it to the wall using the blind-nuts and fasteners. Ensure the enclosure is level and plumb.
5. Verify that all mounting fasteners are tightened securely.

5.3 Installing the Mounting Panel

The zinc-plated mounting panel is pre-installed or supplied separately for internal component mounting.

• If the mounting panel is separate, position it inside the enclosure on the designated mounting studs or rails.
• Secure the mounting panel using the provided hardware.
• Install electrical and electronic components onto the mounting panel as required, ensuring proper spacing and wire management.

5.4 Grounding

Ensure the enclosure and all internal components are properly grounded according to applicable electrical codes. A grounding stud is typically provided within the enclosure for this purpose.

6. Operation

The Rittal 8017637 enclosure is designed for straightforward operation to access internal components.

• Opening the Door: Insert a slotted screwdriver or appropriate tool into the 1/4 turn latches. Rotate the latches 90 degrees counter-clockwise to disengage. The door is hinged on the left side and will swing open to the left.
• Closing the Door: Close the door firmly. Engage the 1/4 turn latches by rotating them 90 degrees clockwise until they are securely fastened. Ensure the door gasket is properly seated to maintain the IP 66 rating.

7. Maintenance

Regular maintenance helps ensure the longevity and protective capabilities of your Rittal enclosure.

• Cleaning: Clean the exterior of the stainless steel enclosure periodically with a mild detergent and water. Avoid abrasive cleaners or harsh chemicals that could damage the finish. Rinse thoroughly and dry with a soft cloth.
• Gasket Inspection: Annually inspect the foamed-in-place polyurethane gasket for signs of wear, cracking, or compression set. A damaged gasket can compromise the enclosure's environmental protection rating. Replace if necessary.
• Latch Inspection: Periodically check the 1/4 turn latches for proper function and security. Ensure they engage smoothly and hold the door firmly closed. Lubricate moving parts with a suitable lubricant if needed.
• Mounting Hardware: Periodically check all mounting fasteners for tightness, especially after initial installation and during routine maintenance.

8. Troubleshooting

This section provides solutions to common issues that may arise with the enclosure.

• Door Not Sealing Properly:
  • Check if the door gasket is clean, intact, and properly seated. Clean or replace the gasket if damaged.
  • Ensure the latches are fully engaged and tightened.
  • Verify that no internal components are obstructing the door closure.
• Latches Are Stiff or Difficult to Operate:
  • Clean any debris from the latch mechanism.
  • Apply a small amount of appropriate lubricant to the moving parts of the latches.
• Enclosure Appears Loose on Wall:
  • Inspect all wall-mounting fasteners. Tighten any loose fasteners.
  • If fasteners continue to loosen, consider reinforcing the mounting surface or using different anchoring hardware.

For issues not covered here, please contact Rittal customer support.

9. Warranty and Support

For information regarding product warranty, technical support, or spare parts, please contact Rittal customer service directly. Contact details can typically be found on the official Rittal website or through your authorized distributor.

10. About Rittal

Rittal LLC is a global manufacturer of industrial and IT enclosures, racks, and accessories, including cooling and power management systems for industrial, data center, outdoor, and hybrid applications. As the largest manufacturer of enclosures in the world, Rittal provides innovative, high-quality solutions for practically any industrial or IT infrastructure application. Products are tested and certified to UL, CSA, ATEX, NEMA, and more. Rittal North America is built on a strong tradition of innovation and takes pride in a progressive approach to engineering comprehensive and effective solutions. Rittal has a proven track record of meeting the challenges faced by its customers, from pioneering the modular enclosure to developing what has become the standard 19-inch server rack for the IT industry, to the use of nanotechnology that drastically improves the efficiency of industrial climate control products.