Introduction
This manual provides instructions for the installation and use of the Leggett & Platt 4-inch Adjustable Bed Leg Kit. This kit is designed to replace existing legs on compatible Leggett & Platt adjustable bed bases, allowing for adjustment of the bed's overall height. Each kit contains four black steel riser legs.
Important Safety Information
Warning: Handle with care to avoid injury from sharp edges. Ensure the bed's total weight, including occupants, does not exceed the weight-bearing capacity of the bed frame and these legs. Always ensure legs are securely tightened before use.
Product Components and Overview
The Leggett & Platt Adjustable Bed Leg Kit includes four (4) individual 4-inch black steel riser legs. Each leg features an M8 threaded bolt for attachment to the bed frame and a glide on the bottom.

Image 1: A single 4-inch black steel adjustable bed leg, showing the M8 threaded bolt at the top.
Each leg is constructed from durable steel with a black finish. The M8 threaded bolt extends approximately 1/2 inch from the top of the leg, designed for secure attachment. A 3/16 inch high glide is integrated into the bottom of each leg to protect flooring.

Image 2: A set of four 4-inch black steel adjustable bed legs. These legs are designed to be used with 7/16" grip ring stem casters, which are sold separately.
These legs also provide a provision for attaching casters. Casters with a 7/16 inch diameter x 1 1/2 inch high stem will fit into the bottom of the riser leg, allowing for mobility if desired (casters sold separately).
Compatibility
This leg kit is specifically designed for most Leggett & Platt adjustable bed bases that utilize M8 threading. It is crucial to verify your bed base's threading before purchase and installation.

Image 3: Visual guide detailing the M8 threaded bolt, approximate 1/2 inch bolt length, and 1 1/2 inch leg diameter. Important note: These legs do NOT fit Sealy or Serta brand frames.
Important Compatibility Notes:
- Does NOT fit Mattress Firm 50 Adjustable bases from Leggett & Platt.
- Does NOT fit Reverie Model Adjustable Beds.
- Does NOT fit Sealy or Serta brand frames.
Always confirm the threading and model of your adjustable bed base to ensure proper fit and function.
Setup and Installation
- Prepare the Bed Base: Carefully lift or tilt your adjustable bed base to access the existing legs or leg attachment points. It is recommended to have assistance to prevent injury or damage to the bed.
- Remove Existing Legs (if applicable): If your bed base has existing legs, unscrew them counter-clockwise until they are fully detached.
- Install New Legs: Align the M8 threaded bolt of the new 4-inch Leggett & Platt leg with the corresponding threaded insert on the bottom of your bed base. Screw the leg clockwise until it is hand-tight.
- Secure All Legs: Repeat the process for all four legs, ensuring each is securely fastened. Do not overtighten, but ensure there is no wobble.
- Position the Bed: Carefully lower the bed base back onto its new legs. Verify that the bed is stable and level before use.
If you plan to attach casters, ensure they are compatible (7/16" diameter x 1 1/2" H Stem) and insert them into the bottom of the legs after the legs are installed on the bed base.
Operation
These legs are fixed-height components designed to provide a stable 4-inch elevation for your adjustable bed. Once installed, the height of the bed is set. The primary "operation" involves the use of your adjustable bed's existing remote control or controls to adjust the bed's position (head, foot, etc.). These legs do not offer independent height adjustment once installed.
Maintenance
- Cleaning: Wipe the legs with a damp cloth to remove dust or debris. Avoid harsh chemicals that may damage the finish.
- Inspection: Periodically check the legs for any signs of damage, wear, or loosening. Ensure they remain securely screwed into the bed base.
- Tightening: If any leg feels loose, gently retighten it by hand.
Troubleshooting
- Legs do not fit: Verify that your bed base uses M8 threading. Confirm your bed is a compatible Leggett & Platt model and not one of the excluded models (Mattress Firm 50, Reverie, Sealy, Serta).
- Bed is unstable/wobbly: Ensure all four legs are fully and securely tightened. Check that the bed base is on a flat, level surface. If using casters, ensure they are properly installed and locked if applicable.
- Damage to flooring: The legs include a glide to protect floors. Ensure this glide is intact. For sensitive flooring, consider placing additional protective pads under each leg.
If issues persist after following these steps, contact Leggett & Platt customer support for further assistance.
Specifications
| Feature | Detail |
|---|---|
| Brand | Leggett & Platt |
| Model Number | 4B1833 |
| Item Type Name | Adjustable Base Riser Legs |
| Material | Alloy Steel |
| Color | Black |
| Height (each leg) | 4 inches |
| Diameter (each leg) | 1 1/2 inches |
| Attaching Bolt | M8 Threading, extends approx. 1/2 inch |
| Glide Height | 3/16 inch |
| Caster Compatibility | 7/16 inch diameter x 1 1/2 inch H Stem casters |
| Number of Pieces | 4 (per set) |
| Installation Type | Screw-In |
| Item Weight (set) | 1.7 pounds |
| Recommended Use | Adjusting the height of compatible Leggett & Platt adjustable beds |
Warranty Information
Specific warranty details for this Leggett & Platt product may vary. Please refer to the documentation provided with your original adjustable bed base or visit the official Leggett & Platt website for the most current warranty information. Keep your purchase receipt as proof of purchase for any warranty claims.
Customer Support
For further assistance, technical support, or inquiries regarding your Leggett & Platt Adjustable Bed Leg Kit, please contact Leggett & Platt customer service. Contact information can typically be found on the official Leggett & Platt website or within the original product packaging of your adjustable bed base.