Fellowes 8041701 Professional Series Dual Monitor Stand

1. Introduction

Thank you for choosing the Fellowes 8041701 Professional Series Dual Monitor Stand. This product is designed to enhance your workspace ergonomics by elevating two monitors to a comfortable viewing height, reducing neck strain and shoulder tension. Its adjustable features allow for optimal positioning, and it helps clear valuable desk space.

This manual provides detailed instructions for the safe and correct assembly, operation, and maintenance of your monitor stand. Please read it thoroughly before installation and retain it for future reference.

2. Safety Information

• Weight Capacity: Do not exceed the maximum weight capacity of 24 lbs per arm. Ensure your monitors are within this limit.
• Stability: Ensure the stand is securely mounted to a stable desk surface. Improper installation can lead to instability and potential damage or injury.
• Adjustments: Exercise caution when making adjustments to prevent monitors from shifting unexpectedly. Always support monitors during adjustments.
• Cable Management: Route cables safely to avoid pinching or snagging, which could damage cables or cause monitors to fall.
• Proposition 65 Warning: This product may expose you to chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

3. Package Contents

Verify that all components are present before beginning assembly. If any parts are missing or damaged, please contact Fellowes customer support.

• Main Pole
• Dual Monitor Arms (2 sections per arm)
• VESA Mounting Plates (2)
• Desk Clamp Assembly
• Grommet Mount Hardware
• Cable Management Clips
• Hardware Kit (screws, washers, Allen wrenches)

Image: All components of the Fellowes 8041701 Professional Series Dual Monitor Stand laid out, including the main pole, dual articulating arms, and VESA mounting plates.

4. Setup Instructions

The Fellowes 8041701 monitor stand offers two mounting options: desk clamp or grommet mount. Choose the method best suited for your desk.

4.1. Desk Clamp Installation

1. Attach the desk clamp assembly to the bottom of the main pole using the provided screws.
2. Position the clamp on the edge of your desk (1"-3" thick) and tighten the clamp screw until the pole is secure.

4.2. Grommet Mount Installation

1. If your desk has a grommet hole, remove the grommet cover.
2. Insert the main pole through the grommet hole.
3. From underneath the desk, secure the pole using the grommet mounting plate and tightening knob.

4.3. Attaching Monitor Arms and Monitors

1. Slide the monitor arm sections onto the main pole at your desired height. Secure them with the locking collars.
2. Attach the VESA mounting plates to the back of your monitors using the appropriate screws from the hardware kit. Ensure the screws are tightened securely.
3. Carefully slide each monitor (with attached VESA plate) onto the end of its respective monitor arm. Ensure the monitor clicks into place or is secured with the locking mechanism.
4. Connect all necessary cables to your monitors and use the integrated cable management clips to route them neatly along the arms and pole.

Image: A rear view of two monitors mounted on the stand, showing the desk clamp mechanism securing the stand to the desk edge and cables routed.

5. Operating Instructions

The Fellowes 8041701 monitor stand offers extensive adjustability to customize your viewing experience.

5.1. Height Adjustment

To adjust the height of the monitors, loosen the locking collar on the main pole, slide the arm assembly up or down to the desired position (3.5 inches to 16.5 inches from the center of the mounting plate), and then re-tighten the collar securely.

5.2. Tilt and Swivel

Each monitor can be tilted up or down by +/- 37 degrees and swiveled left or right at the arm joints. Gently grasp the monitor edges and adjust to your preferred angle. If the monitor sags, tighten the three screws visible on the round pieces at the end of the arm (part J, as per some instruction sheets) to increase tension.

5.3. Rotation

Monitors can be rotated 360 degrees (portrait to landscape orientation) at the VESA mounting plate. Rotate the monitor gently until it locks into the desired orientation.

Image: A person's hand gently adjusting the position of a monitor mounted on the Fellowes dual monitor stand, demonstrating the ease of adjustment.

6. Maintenance

• Cleaning: Wipe the stand with a soft, damp cloth. Avoid abrasive cleaners or solvents.
• Periodic Checks: Periodically check all screws and connections to ensure they remain tight and secure. Re-tighten if necessary.
• Lubrication: No lubrication is required for the moving parts.

7. Troubleshooting

• Monitor Sags or Tilts Downward: This indicates insufficient tension. Locate the three screws on the round pieces at the end of the arm (near the VESA plate) and tighten them with the provided Allen wrench until the monitor holds its position.
• Stand is Unstable: Ensure the desk clamp or grommet mount is fully tightened. Verify that the desk surface is sturdy and capable of supporting the stand and monitors.
• Difficulty Adjusting Height: Loosen the locking collar on the main pole sufficiently before attempting to slide the arm assembly.
• Monitors Not Level: Minor adjustments can be made by slightly loosening the VESA plate screws, leveling the monitor, and re-tightening. For larger discrepancies, check the arm placement on the main pole.

8. Specifications

9. Warranty and Support

Fellowes products are designed for durability and performance. For warranty information or technical support, please visit the official Fellowes website or contact their customer service department. Keep your purchase receipt as proof of purchase.

Fellowes Contact Information:
Please refer to the contact details provided on the Fellowes official website or product packaging for the most current support options.